- 您現在的位置：買賣IC網 > PDF目錄372540 > X93256 Dual Digitally Controlled Potentiometers (XDCPs)(雙數控電位器) PDF資料下載
參數資料
| 型號： | X93256 |
| 元件分類： | 數字電位計 |
| 英文描述： | Dual Digitally Controlled Potentiometers (XDCPs)(雙數控電位器) |
| 中文描述： | 雙數控電位器（XDCPs）（雙數控電位器） |
| 文件頁數： | 8/9頁 |
| 文件大?。?/td> | 186K |
| 代理商： | X93256 |
X93256
8 of 9
REV 1.6 6/22/04
www.xicor.com
INSTRUCTIONS AND PROGRAMMING
The INC, U/D and CS inputs control the movement of the
pertaining wiper along the resistor array. With CS set
LOW the pertaining potentiometer is selected and
enabled to respond to the U/D and INC inputs. HIGH to
LOW transitions on INC will increment or decrement
(depending on the state of the U/D input) a five bit
counter. The output of this counter is decoded to select
one of thirty two wiper positions along the resistive array.
The value of the counter is stored in nonvolatile memory
whenever each CS transitions HIGH while the pertaining
INC input is also HIGH. In order to avoid an accidental
store during power-up, each CS must go HIGH with V
CC
during initial power-up. When left open, each CS pin is
internally pulled up to V
CC
by an internal 30k resistor.
The system may select the X93256, move any wiper and
deselect the device without having to store the latest
wiper position in nonvolatile memory. After the wiper
movement is performed as described above and once the
new position is reached, the system must keep INC LOW
while taking CS HIGH. The new wiper position will be
maintained until changed by the system or until a power-
up/down cycle recalled the previously stored data. In
order to recall the stored position of the wiper on power-
up, the CS pin must be held HIGH.
This procedure allows the system to always power-up to
a preset value stored in nonvolatile memory; then during
system operation minor adjustments could be made. The
adjustments might be based on user preference, system
parameter changes due to temperature drift, or other
system trim requirements.
The state of U/D may be changed while CS remains
LOW. This allows the host system to enable the device
and then move each wiper up and down until the proper
trim is attained.
MODE SELECTION
SYMBOL TABLE
CS
INC
U/D
Mode
L
H
Wiper Up
L
L
Wiper Down
H
X
Store Wiper Position
H
X
X
Standby Current
L
X
No Store, Return to Standby
L
H
Wiper Up (not recommended)
L
L
Wiper Down (not recommended)
WAVEFORM
INPUTS
OUTPUTS
Must be
steady
Will be
steady
May change
from Low to
High
May change
from High to
Low
Will change
from Low to
High
Will change
from High to
Low
Don’t Care:
Changes
Allowed
N/A
Changing:
State Not
Known
Center Line
is High
Impedance
相關PDF資料 |
PDF描述 |
|---|---|
| x9400 | Quad SPI EEPOT Nonvolatile Digital Potentiometer(四SPI EEPOT非易失性數字電位器) |
| X9408(中文) | Quad 2-Wire EEPOT Nonvolatile Digital Potentiometer(4個EEPOT,IIC接口,直接寫入/讀出滑動端位置,低噪聲,非易失性數字電位器) |
| X9408 | Quad 2-Wire EEPOT Nonvolatile Digital Potentiometer(4個EEPOT,IIC接口,直接寫入/讀出滑動端位置,低噪聲,非易失性數字電位器) |
| X9418(中文) | Dual 2-Wire EEPOT Nonvolatile Digital Potentiometer(2個EEPOT,IIC接口,直接寫入/讀出滑動端位置,低噪聲,非易失性數字電位器) |
| X9418 | Dual 2-Wire EEPOT Nonvolatile Digital Potentiometer(2個EEPOT,IIC接口,直接寫入/讀出滑動端位置,低噪聲,非易失性數字電位器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X93256_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual Digitally Controlled Potentiometers |
| X93256_08 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual Digitally Controlled Potentiometers(XDCPs?) |
| X93256UV14I-2.7 | 功能描述:IC XDCP DUAL 32-TAP 50K 14-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
| X93256UV14I-2.7T1 | 功能描述:IC XDCP DUAL 32-TAP 50K 14-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
| X93256UV14IZ-2.7 | 功能描述:IC XDCP DUAL 32TAP 50K 14-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。