- 您現在的位置：買賣IC網 > PDF目錄371290 > X9314WPM3 TRANS PREBIASED PNP 200MW SOT323 PDF資料下載
參數資料
| 型號： | X9314WPM3 |
| 英文描述： | TRANS PREBIASED PNP 200MW SOT323 |
| 中文描述： | E2POT⑩非易失數字電位器 |
| 文件頁數： | 3/10頁 |
| 文件大?。?/td> | 53K |
| 代理商： | X9314WPM3 |
X9314
3
DEVICE OPERATION
There are three sections of the X9314: the input control,
counter and decode section; the nonvolatile memory; and
the resistor array. The input control section operates just
like an up/down counter. The output of this counter is
decoded to turn on a single electronic switch connecting
a point on the resistor array to the wiper output. Under the
proper conditions the contents of the counter can be
stored in nonvolatile memory and retained for future use.
The resistor array is comprised of 31 individual resistors
connected in series. At either end of the array and
between each resistor is an electronic switch that
transfers the potential at that point to the wiper.
The
INC
, U/
D
and
CS
inputs control the movement of the
wiper along the resistor array. With
CS
set LOW the
X9314 is selected and enabled to respond to the
U/
D
and
INC
inputs. HIGH to LOW transitions on
INC
will
increment or decrement (depending on the state of the
U/
D
input) a five bit counter. The output of this counter
is decoded to select one of thirty-two wiper positions
along the resistive array.
The wiper, when at either fixed terminal, acts like its
mechanical equivalent and does not move beyond the
last position. That is, the counter does not wrap around
when clocked to either extreme.
The value of the counter is stored in nonvolatile memory
whenever
CS
transistions HIGH while the
INC
input is
also HIGH.
When the X9314 is powered-down, the last counter
position stored will be maintained in the nonvolatile
memory. When power is restored, the contents of the
memory are recalled and the counter is reset to the value
last stored.
Operation Notes
The system may select the X9314, move the wiper and
deselect the device without having to store the latest
wiper position in nonvolatile memory. The wiper
movement is performed as described above; once the
new position is reached, the system would keep the
INC
LOW while taking
CS
HIGH. The new wiper position
would be maintained until changed by the system or
until a power-up/down cycle recalled the previously
stored data.
This would allow the system to always power-up to a
preset value stored in nonvolatile memory; then during
system operation minor adjustments could be made.
The adjustments might be based on user preference,
system parameter changes due to temperature drift,
etc...
The state of U/
D
may be changed while
CS
remains
LOW. This allows the host system to enable the X9314
and then move the wiper up and down until the proper
trim is attained.
T
IW
/R
TOTAL
The electronic switches on the X9314 operate in a
“make before break” mode when the wiper changes tap
positions. If the wiper is moved several positions mul-
tiple taps are connected to the wiper for t
IW
(
INC
to V
W
change). The R
TOTAL
value for the device can tempo-
rarily be reduced by a significant amount if the wiper is
moved several positions.
R
TOTAL
with V
CC
Removed
The end to end resistance of the array will fluctuate once
V
CC
is removed.
SYMBOL TABLE
WAVEFORM
INPUTS
OUTPUTS
Must be
steady
Will be
steady
May change
from LOW
to HIGH
Will change
from LOW
to HIGH
May change
from HIGH
to LOW
Will change
from HIGH
to LOW
Don’t Care:
Changes
Allowed
N/A
Changing:
State Not
Known
Center Line
is High
Impedance
相關PDF資料 |
PDF描述 |
|---|---|
| X9314WMM3 | DIODE SD101A SHOTKY BARRIER SOD68(DO-34) |
| X9314WM3 | E2POT⑩ Nonvolatile Digital Potentiometer |
| X9314WMI | E2POT⑩ Nonvolatile Digital Potentiometer |
| X9314WMM | E2POT⑩ Nonvolatile Digital Potentiometer |
| X9314WP3 | E2POT⑩ Nonvolatile Digital Potentiometer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9314WS | 功能描述:IC DIG POT 10K 32TP LOG TPR SO8 RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9314WS3 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:E2POT⑩ Nonvolatile Digital Potentiometer |
| X9314WS-3 | 功能描述:IC XDCP SGL 32-TAP 10K 8-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
| X9314WS-3T1 | 功能描述:IC XDCP SGL 32-TAP 10K 8-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
| X9314WS-3T2 | 功能描述:IC XDCP SGL 32-TAP 10K 8-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。