- 您現在的位置：買賣IC網 > PDF目錄371290 > X9313USI (INTERSIL CORP) IGBT Power Module PDF資料下載
參數資料
| 型號： | X9313USI |
| 廠商： | INTERSIL CORP |
| 元件分類： | 數字電位計 |
| 英文描述： | IGBT Power Module |
| 中文描述： | 50K DIGITAL POTENTIOMETER, INCREMENT/DECREMENT CONTROL INTERFACE, 32 POSITIONS, PDSO8 |
| 封裝： | PLASTIC, MS-012AA, SOIC-8 |
| 文件頁數： | 3/10頁 |
| 文件大?。?/td> | 50K |
| 代理商： | X9313USI |
X9313
3
DEVICE OPERATION
There are three sections of the X9313: the input control,
counter and decode section; the nonvolatile memory;
and the resistor array. The input control section
operates just like an up/down counter. The output of this
counter is decoded to turn on a single electronic switch
connecting a point on the resistor array to the wiper
output. Under the proper conditions the contents of the
counter can be stored in nonvolatile memory and
retained for future use. The resistor array is comprised
of 31 individual resistors connected in series. At either
end of the array and between each resistor is an
electronic switch that transfers the potential at that point
to the wiper.
The
INC
, U/
D
and
CS
inputs control the movement of the
wiper along the resistor array. With
CS
set LOW the
X9313 is selected and enabled to respond to the
U/
D
and
INC
inputs. HIGH to LOW transitions on
INC
will
increment or decrement (depending on the state of the
U/
D
input) a seven bit counter. The output of this counter
is decoded to select one of thirty two wiper positions
along the resistive array.
The wiper, when at either fixed terminal, acts like its
mechanical equivalent and does not move beyond the
last position. That is, the counter does not wrap around
when clocked to either extreme.
The value of the counter is stored in nonvolatile memory
whenever
CS
transistions HIGH while the
INC
input is
also HIGH.
When the X9313 is powered-down, the last counter
position stored will be maintained in the nonvolatile
memory. When power is restored, the contents of the
memory are recalled and the counter is reset to the value
last stored.
Operation Notes
The system may select the X9313, move the wiper and
deselect the device without having to store the latest
wiper position in nonvolatile memory. The wiper move-
ment is performed as described above; once the new
position is reached, the system would the keep
INC
LOW while taking
CS
HIGH. The new wiper position
would be maintained until changed by the system or
until a power-up/down cycle recalled the previously
stored data.
This would allow the system to always power-up to a
preset value stored in nonvolatile memory; then during
system operation minor adjustments could be made.
The adjustments might be based on user preference,
system parameter changes due to temperature drift,
etc...
The state of U/
D
may be changed while
CS
remains
LOW. This allows the host system to enable the X9313
and then move the wiper up and down until the proper
trim is attained.
T
IW
/R
TOTAL
The electronic switches on the X9313 operate in a
“make before break” mode when the wiper changes tap
positions. If the wiper is moved several positions mul-
tiple taps are connected to the wiper for t
IW
(
INC
to V
W
change). The R
TOTAL
value for the device can tempo-
rarily be reduced by a significant amount if the wiper is
moved several positions.
R
TOTAL
with V
CC
Removed
The end to end resistance of the array will fluctuate once
V
CC
is removed.
SYMBOL TABLE
WAVEFORM
INPUTS
OUTPUTS
Must be
steady
Will be
steady
May change
from LOW
to HIGH
Will change
from LOW
to HIGH
May change
from HIGH
to LOW
Will change
from HIGH
to LOW
Don’t Care:
Changes
Allowed
N/A
Changing:
State Not
Known
Center Line
is High
Impedance
相關PDF資料 |
PDF描述 |
|---|---|
| X9313USM | IGBT Power Module |
| X9313USZ | IGBT Power Module |
| X9313ZSZ | Circular Connector; Body Material:Aluminum; Series:PT00; No. of Contacts:30; Connector Shell Size:18; Connecting Termination:Crimp; Circular Shell Style:Wall Mount Receptacle; Circular Contact Gender:Pin; Insert Arrangement:18-30 |
| X9313ZMIZ | Terminal Voltages +-5V, 32 Taps |
| X9313WSIZ | Terminal Voltages +-5V, 32 Taps |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9313USI3 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:E2POT⑩ Nonvolatile Digital Potentiometer |
| X9313USI-3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Digital Potentiometer |
| X9313USIT1 | 功能描述:IC XDCP 32-TAP 50K 3-WIRE 8-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
| X9313USIZ | 功能描述:IC XDCP 32-TAP 50K 3-WIRE 8-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9313USIZT1 | 功能描述:IC XDCP 32-TAP 50K 3-WIRE 8-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。