- 您現在的位置：買賣IC網 > PDF目錄376446 > X9261US24Z (INTERSIL CORP) Dual Digitally-Controlled Potentiometers PDF資料下載
參數資料
| 型號： | X9261US24Z |
| 廠商： | INTERSIL CORP |
| 元件分類： | 數字電位計 |
| 英文描述： | Dual Digitally-Controlled Potentiometers |
| 中文描述： | DUAL 50K DIGITAL POTENTIOMETER, 3-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, PDSO24 |
| 封裝： | 0.300 INCH, ROHS COMPLIANT, PLASTIC, MS-013AD, SOIC-24 |
| 文件頁數： | 4/20頁 |
| 文件大?。?/td> | 370K |
| 代理商： | X9261US24Z |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
4
FN8171.4
October 12, 2006
H
OLD
(HOLD)
HOLD is used in conjunction with the CS pin to select
the device. Once the part is selected and a serial
sequence is underway, HOLD may be used to pause
the serial communication with the controller without
resetting the serial sequence. To pause, HOLD must
be brought LOW while SCK is LOW. To resume
communication, HOLD is brought HIGH, again while
SCK is LOW. If the pause feature is not used, HOLD
should be held HIGH at all times.
D
EVICE
A
DDRESS
(A1 - A0)
The address inputs are used to set the 4-bit slave
address. A match in the slave address serial data
stream must be made with the address input in order
to initiate communication with the X9261.
C
HIP
S
ELECT
(CS)
When CS is HIGH, the X9261 is deselected and the
SO pin is at high impedance, and (unless an internal
write cycle is underway) the device will be in the
standby state. CS LOW enables the X9261, placing it
in the active power mode. It should be noted that after
a power-up, a HIGH to LOW transition on CS is
required prior to the start of any operation.
Potentiometer Pins
R
H
, R
L
The R
H
and R
L
pins are equivalent to the terminal
connections on a mechanical potentiometer. Since
there are 2 potentiometers, there are 2 sets of R
H
and
R
L
such that R
H0
and R
L0
are the terminals of POT 0
and so on.
R
W
The wiper pin are equivalent to the wiper terminal of a
mechanical potentiometer. Since there are 2
potentiometers, there are 2 sets of R
W
such that R
W0
is the terminals of POT 0 and so on.
Supply Pins
S
YSTEM
S
UPPLY
V
OLTAGE
(V
CC
)
AND
S
UPPLY
G
ROUND
(V
SS
)
The V
CC
pin is the system supply voltage. The V
SS
pin is the system ground.
Other Pins
N
O
C
ONNECT
No connect pins should be left floating. This pins are
used for Intersil manufacturing and testing purposes.
H
ARDWARE
W
RITE
P
ROTECT
I
NPUT
(WP)
The WP pin when LOW prevents nonvolatile writes to
the Data Registers.
PRINCIPLES OF OPERATION
Serial Interface
The X9261 supports the SPI interface hardware
conventions. The device is accessed via the SI input
with data clocked in on the rising SCK. CS must be
LOW and the HOLD and WP pins must be HIGH
during the entire operation.
The SO and SI pins can be connected together, since
they have three state outputs. This can help to reduce
system pin count.
Array Description
The X9261 is comprised of a resistor array (See
Figure 1). The array contains the equivalent of 255
discrete resistive segments that are connected in
series. The physical ends of each array are equivalent
to the fixed terminals of a mechanical potentiometer
(R
H
and R
L
inputs).
At both ends of each array and between each resistor
segment is a CMOS switch connected to the wiper
(R
W
) output. Within each individual array only one
switch may be turned on at a time.
These switches are controlled by a Wiper Counter
Register (WCR). The 8-bits of the WCR (WCR[7:0])
are decoded to select, and enable, one of 256
switches (See Table 1).
Power-up and Down Requirements.
There are no restrictions on the power-up or power-
down conditions of V
CC
and the voltages applied to
the potentiometer pins provided that V
CC
is always
more positive than or equal to V
H
, V
L
, and V
W
, i.e.,
V
CC
, V
H
, V
L
, V
W
. The V
CC
ramp rate specification is
always in effect.
X9261
相關PDF資料 |
PDF描述 |
|---|---|
| X9268TS24IZ | Dual Digitally-Controlled Potentiometers |
| X9268TS24IZ-2.7 | Dual Digitally-Controlled Potentiometers |
| X9268TS24Z | Dual Digitally-Controlled Potentiometers |
| X9268US24IZ | Dual Digitally-Controlled Potentiometers |
| X9268US24Z | Dual Digitally-Controlled Potentiometers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9261US24Z-2.7 | 功能描述:IC XDCP DUAL 256TAP 50K 24-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
| X9261US24Z-2.7T1 | 功能描述:IC XDCP DUAL 256TAP 50K 24-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
| X9261US24ZT1 | 功能描述:IC XDCP DUAL 256TAP 50K 24-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
| X9261UV24 | 功能描述:IC XDCP DUAL 256TAP 50K 24-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9261UV24-2.7 | 功能描述:IC XDCP DUAL 256TAP 50K 24-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。