- 您現在的位置：買賣IC網 > PDF目錄371281 > X9252TV24-2.7 Quad Digitally-Controlled (XDCP) potentiometer PDF資料下載
參數資料
| 型號： | X9252TV24-2.7 |
| 元件分類： | 數字電位計 |
| 英文描述： | Quad Digitally-Controlled (XDCP) potentiometer |
| 中文描述： | 四數字控制（數字電位器）電位 |
| 文件頁數： | 16/21頁 |
| 文件大?。?/td> | 126K |
| 代理商： | X9252TV24-2.7 |
X9252
16 of 21
REV 1.4.1 7/29/03
www.xicor.com
Byte Write Operation
For any Byte Write operation, the X9252 requires the
Slave Address byte, an Address Byte, and a Data Byte
(See Figure 6). After each of them, the X9252
responds with an ACK. The master then terminates the
transfer by generating a STOP condition. At this time, if
the write operation is to a volatile register (WCR, or
SR), the X9252 is ready for the next read or write
operation. If the write operation is to a nonvolatile
register (DR), and the WP pin is high, the X9252
begins the internal write cycle to the nonvolatile
memory. During the internal nonvolatile write cycle, the
X9252 does not respond to any requests from the
master. The SDA output is at high impedance.
The SR bits and WP pin determine the register being
accessed through the 2-wire interface. See Table 1 on
page 11.
As noted before, that any write operation to a Data
Register (DR), also writes to the WCR of the corre-
sponding DCP.
For example, to write 3Ahex to the Data Register 1 of
DCP2 the following sequence is required:
During the sequence of this example, WP pin must be
high, and A0, A1, and A2 pins must be low. When com-
pleted, the DR21 register will be set to 3Ah, and also
the WCR2.
Figure 6. Byte Write Sequence
START
Slave Address
ACK
Address Byte
ACK
Data Byte
ACK
STOP
0101 0000
0000 0111
0000 0011
START
Slave Address
ACK
Address Byte
ACK
Data Byte
ACK
STOP
0101 0000
0000 0010
0011 1010
(Hardware Address = 000,
and a Write command)
(Indicates Status Register
address)
(Data Register 1 and
NVEnable selected)
(Hardware address = 000,
Write command)
(Access DCP2)
(Write Data Byte 3Ah)
S
t
a
r
t
S
t
o
p
Slave
Address
Address
Byte
Data
Byte
A
C
K
Signals from
the Master
Signals from
the Slave
A
C
K
0
0
0
1
1
A
C
K
Write
Signal at SDA
相關PDF資料 |
PDF描述 |
|---|---|
| X9252 | Quad Digitally-Controlled (XDCP) potentiometer |
| X9252WV24-2.7 | Quad Digitally-Controlled (XDCP) potentiometer |
| X9252TS24I-2.7 | Low Power + Quad 256-Tap + 2-Wire Bus + Up/Down Interface |
| X9252TS24IZ-2.7 | Low Power + Quad 256-Tap + 2-Wire Bus + Up/Down Interface |
| X9252WS24IZ-2.7 | RPK-742C083101J OK TO USE MFG P/N CN1J4LTD101J |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9252TV24I-2.7 | 功能描述:IC DCP QUAD 100K 256TAP 24-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9252TV24IZ-2.7 | 功能描述:IC POT DGTL QUAD 100KOHM 24TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9252US24I-2.7 | 功能描述:IC XDCP QUAD 256TAP 50K 24-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9252US24IZ-2.7 | 制造商:Intersil Corporation 功能描述:DGTL POTENTIOMETER 256POS 50KOHM QUAD 24SOIC W - Rail/Tube 制造商:Rochester Electronics LLC 功能描述: |
| X9252UV24-2.7 | 功能描述:IC DCP QUAD 250K 256TAP 24-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
發(fā)布緊急采購，3分鐘左右您將得到回復。