- 您現在的位置：買賣IC網 > PDF目錄9131 > X9118TV14-2.7 (Intersil)IC XDCP SGL 1024TAP 100K 14TSSOP PDF資料下載
參數資料
| 型號： | X9118TV14-2.7 |
| 廠商： | Intersil |
| 文件頁數： | 12/17頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC XDCP SGL 1024TAP 100K 14TSSOP |
| 標準包裝： | 95 |
| 系列： | XDCP™ |
| 接片： | 1024 |
| 電阻（歐姆）： | 100k |
| 電路數： | 1 |
| 溫度系數： | 標準值 ±300 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 14-TSSOP |
| 包裝： | 管件 |
4
FN8161.4
December 4, 2009
At both ends of each array and between each resistor
segment is a CMOS switch (transmission gate) connected to
the wiper (RW) output. Within each individual array only one
switch may be turned on at a time. These switches are
controlled by the Wiper Counter Register (WCR). The
10-bits of the WCR (WCR[9:0]) are decoded to select, and
enable, one of 1024 switches.
The WCR may be written directly. The Data Registers and
the WCR can be read and written by the host system.
Serial Interface Description
SERIAL INTERFACE – 2-WIRE
The X9118 supports a bidirectional bus oriented protocol.
The protocol defines any device that sends data onto the
bus as a transmitter and the receiving device as the receiver.
The device controlling the transfer is a master and the
device being controlled is the slave. The master will always
initiate data transfers and provide the clock for both transmit
and receive operations. Therefore, the X9118 will be
considered a slave device in all applications.
CLOCK AND DATA CONVENTIONS
Data states on the SDA line can change only during SCL
LOW periods. SDA state changes during SCL HIGH are
reserved for indicating start and stop conditions. See Figure 3.
START CONDITION
All commands to the X9118 are preceded by the start
condition, which is a HIGH to LOW transition of SDA while
SCL is HIGH. The X9118 continuously monitors the SDA
and SCL lines for the start condition and will not respond to
any command until this condition is met. See Figure 3.
STOP CONDITION
All communications must be terminated by a stop condition,
which is a LOW to HIGH transition of SDA while SCL is
HIGH. See Figure 3.
ACKNOWLEDGE
Acknowledge is a software convention used to provide a
positive handshake between the master and slave devices
on the bus to indicate the successful receipt of data. The
transmitting device, either the master or the slave, will
release the SDA bus after transmitting eight bits. The master
generates a ninth clock cycle and during this period the
receiver pulls the SDA line LOW to acknowledge that it
successfully received the eight bits of data.
The X9118 will respond with an acknowledge after
recognition of a start condition and its slave address and
once again after successful receipt of the command byte. If
the command is followed by a data byte, the X9118 will
respond with a final acknowledge. See Figure 2.
SERIAL DATA PATH
FROM INTERFACE
REGISTER 0
SERIAL
BUS
INPUT
PARALLEL
BUS
INPUT
COUNTER
REGISTER
R H
R L
R
W
10
C
O
U
N
T
E
R
D
E
C
O
D
E
If WCR = 000[HEX] then RW = RL
If WCR = 3FF[HEX] then RW = RH
WIPER
(WCR)
(DR0)
CIRCUITRY
REGISTER 1
(DR1)
REGISTER 2
(DR2)
REGISTER 3
(DR3)
FIGURE 1. DETAILED POTENTIOMETER BLOCK DIAGRAM
X9118
相關PDF資料 |
PDF描述 |
|---|---|
| VE-27X-MY-F2 | CONVERTER MOD DC/DC 5.2V 50W |
| V375A36T600BG | CONVERTER MOD DC/DC 36V 600W |
| VE-27X-MY-F1 | CONVERTER MOD DC/DC 5.2V 50W |
| M83723/95R1005N | CONN PLUG 5POS STRAIGHT W/SCKT |
| VE-26N-MW-S | CONVERTER MOD DC/DC 18.5V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9118TV14I | 功能描述:IC DCP 100K 1024TP 14TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9118TV14I-2.7 | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9118TV14IZ | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9118TV14IZ-2.7 | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9118TV14Z | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。