- 您現在的位置：買賣IC網 > PDF目錄9133 > X9111TV14I-2.7 (Intersil)IC XDCP SGL 1024TAP 100K 14TSSOP PDF資料下載
參數資料
| 型號： | X9111TV14I-2.7 |
| 廠商： | Intersil |
| 文件頁數： | 11/17頁 |
| 文件大小： | 0K |
| 描述： | IC XDCP SGL 1024TAP 100K 14TSSOP |
| 標準包裝： | 95 |
| 系列： | XDCP™ |
| 接片： | 1024 |
| 電阻（歐姆）： | 100k |
| 電路數： | 1 |
| 溫度系數： | 標準值 ±300 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | 6 線 SPI（芯片選擇，設備位址） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 14-TSSOP |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁
3
FN8159.4
September 15, 2006
Pin Descriptions
Bus Interface Pins
SERIAL OUTPUT (SO)
SO is a serial data output pin. During a read cycle, data is
shifted out on this pin. Data is clocked out by the falling edge
of the serial clock.
SERIAL INPUT (SI)
SI is the serial data input pin. All opcodes, byte addresses and
data to be written to the pots and pot registers are input on this
pin. Data is latched by the rising edge of the serial clock.
SERIAL CLOCK (SCK)
The SCK input is used to clock data into and out of the
X9111.
HOLD (HOLD)
HOLD is used in conjunction with the CS pin to select the
device. Once the part is selected and a serial sequence is
underway, HOLD may be used to pause the serial
communication with the controller without resetting the serial
sequence. To pause, HOLD must be brought LOW while SCK is
LOW. To resume communication, HOLD is brought HIGH, again
while SCK is LOW. If the pause feature is not used, HOLD should
be held HIGH at all times.
DEVICE ADDRESS (A0, A1)
The address inputs are used to set the 8-bit slave address. A
match in the slave address serial data stream must be made
with the address input (A1–A0) in order to initiate
communication with the X9111.
CHIP SELECT (CS)
When CS is HIGH, the X9111 is deselected and the SO pin is at
high impedance, and (unless an internal write cycle is
underway) the device will be in the standby state. CS LOW
enables the X9111, placing it in the active power mode. It
should be noted that after a power-up, a HIGH to LOW
transition on CS is required prior to the start of any operation.
HARDWARE WRITE PROTECT INPUT (WP)
The WP pin when LOW prevents nonvolatile writes to the
Data Registers.
Potentiometer Pins
RH, RL
The RH and RL pins are equivalent to the terminal connections
on a mechanical potentiometer.
RW
The wiper pin is equivalent to the wiper terminal of a
mechanical potentiometer.
Bias Supply Pins
SYSTEM SUPPLY VOLTAGE (VCC) AND SUPPLY
GROUND (VSS)
The VCC pin is the system supply voltage. The VSS pin is
the system ground.
Other Pins
NO CONNECT (NC)
Pin should be left open. This pin is used for Intersil
manufacturing and test purposes.
Principles of Operation
Device Description
Serial Interface
The X9111 supports the SPI interface hardware conventions.
The device is accessed via the SI input with data clocked-in on
the rising SCK. CS must be LOW and the HOLD and WP pins
must be HIGH during the entire operation.
The SO and SI pins can be connected together, since they
have three state outputs. This can help to reduce system pin
count.
Array Description
The X9111 is comprised of a resistor array (see Figure 1).
The array contains the equivalent of 1023 discrete resistive
segments that are connected in series. The physical ends of
each array are equivalent to the fixed terminals of a
mechanical potentiometer (RH and RL inputs).
At both ends of each array and between each resistor
segment is a CMOS switch connected to the wiper (RW)
output. Within the individual array only one switch may be
turned on at a time.
Pin Descriptions
PIN
(TSSOP)
SYMBOL
FUNCTION
1
SO
Serial Data Output
2
A0
Device Address
3
NC
No Connect
4CS
Chip Select
5
SCK
Serial Clock
6
SI
Serial Data Input
7VSS
System Ground
8WP
Hardware Write Protect
9
A1
Device Address
10
HOLD
Device Select. Pause the Serial Bus
11
RW
Wiper Terminal of the Potentiometer
12
RH
High Terminal of the Potentiometer
13
RL
Low Terminal of the Potentiometer
14
VCC
System Supply Voltage
X9111
相關PDF資料 |
PDF描述 |
|---|---|
| MS27474E18B96P | CONN RCPT 9POS JAM NUT W/PINS |
| MS27468T25F29PB | CONN RCPT 29POS JAM NUT W/PINS |
| M83723/73R22197 | CONN RCPT 19POS JAM NUT W/SCKT |
| V375A36T600BF3 | CONVERTER MOD DC/DC 36V 600W |
| M83723/73R22196 | CONN RCPT 19POS JAM NUT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9111TV14IZ | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9111TV14IZ-2.7 | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 35 ppm/°C 存儲器類型:非易失 接口:3 線串口 電源電壓:2.7 V ~ 5.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN-EP（3x3） 包裝:剪切帶 (CT) 產品目錄頁面:1399 (CN2011-ZH PDF) 其它名稱:MAX5423ETA+TCT |
| X9111TV14IZ-2.7T1 | 功能描述:IC POT DGTL 100K OHM 14-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9111TV14Z | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9111TV14Z-2.7 | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。