- 您現在的位置：買賣IC網 > PDF目錄371273 > X76F641W-2.0 Secure SerialFlash PDF資料下載
參數資料
| 型號： | X76F641W-2.0 |
| 英文描述： | Secure SerialFlash |
| 中文描述： | 安全SerialFlash |
| 文件頁數： | 2/17頁 |
| 文件大小： | 116K |
| 代理商： | X76F641W-2.0 |
X76F641
2
PIN DESCRIPTIONS
Serial Clock (SCL)
The SCL input is used to clock all data into and out of the
device.
Serial Data (SDA)
SDA is a true three state serial data input/output pin. Dur-
ing a read cycle, data is shifted out on this pin. During a
write cycle, data is shifted in on this pin. In all other
cases, this pin is in a high impedance state.
Reset (RST)
RST is a device reset pin. When RST is pulsed high the
X76F641 will output 32 bits of fixed data which conforms
to the standard for “synchronous response to reset”. The
part must not be in a write cycle for the response to reset
to occur. See Figure 11. If there is power interrupted dur-
ing the Response to Reset, the response to reset will be
aborted and the part will return to the standby state. The
response to reset is "mask programmable" only!
DEVICE OPERATION
There are two primary modes of operation for the
X76F641; Protected READ and protected WRITE.
Protected operations must be performed with one of four
8-byte passwords.
The basic method of communication for the device is
generating a start condition, then transmitting a com-
mand, followed by the correct password. All parts will be
shipped from the factory with all passwords equal to ‘0’.
The user must perform ACK Polling to determine the
validity of the password, before starting a data transfer
(see Acknowledge Polling.) Only after the correct pass-
word is accepted and a ACK polling has been performed,
can the data transfer occur.
To ensure the correct communication, RST must remain
LOW under all conditions except when running a
“Response to Reset sequence”.
Data is transferred in 8-bit segments, with each transfer
being followed by an ACK, generated by the receiving
device.
If the X76F641 is in a nonvolatile write cycle a “no ACK”
(SDA=High) response will be issued in response to load-
ing of the command byte. If a stop is issued prior to the
nonvolatile write cycle the write operation will be termi-
nated and the part will reset and enter into a standby
mode.
The basic sequence is illustrated in Figure 1.
PIN NAMES
PIN CONFIGURATION
After each transaction is completed, the X76F641 will
reset and enter into a standby mode. This will also be the
response if an unsuccessful attempt is made to access a
protected array.
Symbol
SDA
SCL
RST
Vcc
Vss
NC
Description
Serial Data Input/Output
Serial Clock Input
Reset Input
Supply Voltage
Ground
No Connect
SDA
V
CC
RST
SCL
NC
1
2
3
4
7
8
6
5
EIAJ SOIC
V
CC
RST
SCL
V
SS
NC
SDA
Smart Card
NC
NC
7025 FM
02
NC
GND
NC
相關PDF資料 |
PDF描述 |
|---|---|
| X76F641H-2.0 | Secure SerialFlash |
| X76F641HE | Secure SerialFlash |
| X76F641XE | Secure SerialFlash |
| X7R | (144.39 k) |
| X84041SI2.7 | Serial EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X76F641WE | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Secure SerialFlash |
| X76F641WE-2.0 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Secure SerialFlash |
| X76F641WEG | 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:Secure Serial Flash |
| X76F641WEG-2.0 | 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:Secure Serial Flash |
| X76F641WG | 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:Secure Serial Flash |
發布緊急采購，3分鐘左右您將得到回復。