- 您現在的位置：買賣IC網 > PDF目錄371270 > X76F102 The X76F102 is a Password Access Security Supervisor, containing one 896-bit Secure SerialFlash array PDF資料下載
參數資料
| 型號： | X76F102 |
| 英文描述： | The X76F102 is a Password Access Security Supervisor, containing one 896-bit Secure SerialFlash array |
| 中文描述： | 該X76F102是一個密碼訪問安全主管，包含一個896位安全SerialFlash陣列 |
| 文件頁數： | 3/18頁 |
| 文件大?。?/td> | 103K |
| 代理商： | X76F102 |
X76F102
3
After each transaction is completed, the X76F102 will
reset and enter into a standby mode. This will also be the
response if an unsuccessful attempt is made to access a
protected array.
Figure 1. X76F102 Device Operation
Retry Counter
The X76F102 contains a retry counter. The retry counter
allows 8 accesses with an invalid password before any
action is taken. The counter will increment with any com-
bination of incorrect passwords. If the retry counter over-
flows, the memory area and both of the passwords are
cleared to "0". If a correct password is received prior to
retry counter overflow, the retry counter is reset and
access is granted.
Device Protocol
The X76F102 supports a bidirectional bus oriented pro-
tocol. The protocol defines any device that sends data
onto the bus as a transmitter and the receiving device as
a receiver. The device controlling the transfer is a master
and the device being controlled is the slave. The master
will always initiate data transfers and provide the clock for
both transmit and receive operations. Therefore, the
X76F102 will be considered a slave in all applications.
Clock and Data Conventions
Data states on the SDA line can change only during SCL
LOW. SDA changes during SCL HIGH are reserved for
indicating start and stop conditions. Refer to Figure 2 and
Figure 3.
Start Condition
All commands are preceeded by the start condition,
which is a HIGH to LOW transition of SDA when SCL is
HIGH. The X76F102 continuously monitors the SDA and
SCL lines for the start condition and will not respond to
any command until this condition is met.
A start may be issued to terminate the input of a control
byte or the input data to be written. This will reset the
device and leave it ready to begin a new read or write
command. Because of the push/pull output, a start can-
not be generated while the part is outputting data. Starts
are inhibited while a write is in progress.
Stop Condition
All communications must be terminated by a stop condi-
tion. The stop condition is a LOW to HIGH transition of
SDA when SCL is HIGH. The stop condition is also used
to reset the device during a command or data input
sequence and will leave the device in the standby power
mode. As with starts, stops are inhibited when outputting
data and while a write is in progress.
Acknowledge
Acknowledge is a software convention used to indicate
successful data transfer. The transmitting device, either
master or slave, will release the bus after transmitting
eight bits. During the ninth clock cycle the receiver will
pull the SDA line LOW to acknowledge that it received
the eight bits of data.
The X76F102 will respond with an acknowledge after
recognition of a start condition and its slave address. If
both the device and a write condition have been
selected, the X76F102 will respond with an acknowledge
after the receipt of each subsequent eight-bit word.
LOAD COMMAND/ADDRESS BYTE
LOAD 8-BYTE
PASSWORD
VERIFY PASSWORD
ACCEPTANCE BY
USE OF ACK POLLING
READ/WRITE
DATA
BYTES
相關PDF資料 |
PDF描述 |
|---|---|
| X76F102H | The X76F102 is a Password Access Security Supervisor, containing one 896-bit Secure SerialFlash array |
| X76F102H-2 | The X76F102 is a Password Access Security Supervisor, containing one 896-bit Secure SerialFlash array |
| X76F102W-2 | The X76F102 is a Password Access Security Supervisor, containing one 896-bit Secure SerialFlash array |
| X76F102HI-2 | The X76F102 is a Password Access Security Supervisor, containing one 896-bit Secure SerialFlash array |
| X76F102V8-2 | The X76F102 is a Password Access Security Supervisor, containing one 896-bit Secure SerialFlash array |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X76F102H | 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:Secure SerialFlash |
| X76F102H-2 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:The X76F102 is a Password Access Security Supervisor, containing one 896-bit Secure SerialFlash array |
| X76F102H-2.0 | 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:Secure SerialFlash |
| X76F102HG | 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:Secure SerialFlash |
| X76F102HG-2.0 | 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:Secure SerialFlash |
發布緊急采購，3分鐘左右您將得到回復。