- 您現在的位置：買賣IC網 > PDF目錄371269 > X76F100PI 1K 128 x 8 Bit PDF資料下載
參數資料
| 型號： | X76F100PI |
| 英文描述： | 1K 128 x 8 Bit |
| 中文描述： | 每1000 128 × 8位 |
| 文件頁數： | 7/17頁 |
| 文件大?。?/td> | 275K |
| 代理商： | X76F100PI |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
X76F100
Characteristics subject to change without notice.
7 of 16
REV 1.0 6/22/00
www.xicor.com
PASSWORDS
Passwords are changed by sending the “change read
password” or “change write password” commands in a
normal sector write operation. A full eight bytes con-
taining the new password must be sent, following suc-
cessful transmission of the current write password and
a valid password ACK response. The user can use a
repeated ACK Polling command to check that a new
password has been written correctly. An ACK indicates
that the new password is valid.
There is no way to read any of the passwords.
Response to Reset (Default = 19 00 AA 55)
The ISO Response to reset is controlled by the RST,
CS and CLK pins. When RST is pulsed high, while CS
is low, the device will output 32-bits of data, one bit per
clock. This conforms to the ISO standard for “synchro-
nous response to reset”. CS must remain LOW and the
part must not be in a write cycle for the response to
reset to occur.
After initiating a nonvolatile write cycle the RST pin
must not be pulsed until the nonvolatile write cycle is
complete. If not, the ISO response will not be acti-
vated. Also, any attempt to pulse the RST pin in the
middle of an ISO transaction will stop the transaction
with the SDA pin in high impedance. The user will have
to issue a stop condition and start the transaction
again. If at any time during the Response to Reset CS
goes HIGH, the response to reset will be aborted and
the part will return to the standby state. A Response to
Reset is not available during a nonvolatile write cycle.
Continued clocks after the 32-bits, will output the 32-bit
sequence again, starting at byte 0.
Figure 7. Response to RESET(RST)
CS
SCK
SO
RST
Byte
0
MSB
LSB
LSB
MSB
1
LSB
MSB
LSB
MSB
2
3
1 0 0
0 0
1 1
1
0
0
0
0 0 0 0 0
0
0
0
0
1
1 0
1
1
1
0
0
0
1
1
0
相關PDF資料 |
PDF描述 |
|---|---|
| X76F100PI-3.0 | 1K 128 x 8 Bit |
| X76F100S8 | 1K 128 x 8 Bit |
| X76F100S8-3.0 | 1K 128 x 8 Bit |
| X76F100S8I | CLAMP |
| X76F100S8I-3.0 | 1K 128 x 8 Bit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X76F100PI-3.0 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:1K 128 x 8 Bit |
| X76F100S8 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:1K 128 x 8 Bit |
| X76F100S8-3.0 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:1K 128 x 8 Bit |
| X76F100S8I | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:1K 128 x 8 Bit |
| X76F100S8I-3.0 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:1K 128 x 8 Bit |
發布緊急采購，3分鐘左右您將得到回復。