- 您現在的位置：買賣IC網 > PDF目錄376443 > X60008DIS8-25 (INTERSIL CORP) Precision 2.5V FGA⑩ Voltage Reference PDF資料下載
參數資料
| 型號： | X60008DIS8-25 |
| 廠商： | INTERSIL CORP |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Precision 2.5V FGA⑩ Voltage Reference |
| 中文描述： | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 2.5 V, PDSO8 |
| 封裝： | 0.150 INCH, SOIC-8 |
| 文件頁數： | 7/10頁 |
| 文件大?。?/td> | 306K |
| 代理商： | X60008DIS8-25 |
7
FN8140.1
May 24, 2006
APPLICATIONS INFORMATION
FGA Technology
The X60008 series of voltage references use the float-
ing gate technology to create references with very low
drift and supply current. Essentially the charge stored
on a floating gate cell is set precisely in manufacturing.
The reference voltage output itself is a buffered ver-
sion of the floating gate voltage. The resulting refer-
ence device has excellent characteristics which are
unique in the industry: very low temperature drift, high
initial accuracy, and almost zero supply current. Also,
the reference voltage itself is not limited by voltage
bandgaps or zener settings, so a wide range of refer-
ence voltages can be programmed (standard voltage
settings are provided, but customer-specific voltages
are available).
The process used for these reference devices is a
floating gate CMOS process, and the amplifier circuitry
uses CMOS transistors for amplifier and output tran-
sistor circuitry. While providing excellent accuracy,
there are limitations in output noise level and load reg-
ulation due to the MOS device characteristics. These
limitations are addressed with circuit techniques dis-
cussed in other sections.
Nanopower Operation
Reference devices achieve their highest accuracy
when powered up continuously, and after initial stabili-
zation has taken place. This drift can be eliminated by
leaving the power-on continuously.
The X60008 is the first high precision voltage reference
with ultra low power consumption that makes it possible
to leave power-on continuously in battery operated cir-
cuits. The X60008 consumes extremely low supply cur-
rent due to the proprietary FGA technology. Supply
current at room temperature is typically 500nA which is
1 to 2 orders of magnitude lower than competitive
devices. Application circuits using battery power will
benefit greatly from having an accurate, stable refer-
ence which essentially presents no load to the battery.
In particular, battery powered data converter circuits
that would normally require the entire circuit to be dis-
abled when not in use can remain powered up
between conversions as shown in figure 1. Data acqui-
sition circuits providing 12 to 24 bits of accuracy can
operate with the reference device continuously biased
with no power penalty, providing the highest accuracy
and lowest possible long term drift.
Other reference devices consuming higher supply cur-
rents will need to be disabled in between conversions
to conserve battery capacity. Absolute accuracy will
suffer as the device is biased and requires time to set-
tle to its final value, or, may not actually settle to a final
value as power-on time may be short.
Figure 1.
Board mounting Considerations
For applications requiring the highest accuracy, board
mounting location should be reviewed. Placing the
device in areas subject to slight twisting can cause
degradation of the accuracy of the reference voltage
due to die stresses. It is normally best to place the
device near the edge of a board, or the shortest side,
as the axis of bending is most limited at that location.
Obviously mounting the device on flexprint or
extremely thin PC material will likewise cause loss of
reference accuracy.
Noise Performance and Reduction:
The output noise voltage in a 0.1Hz to 10Hz
bandwidth is typically 30μVp-p. This is shown in the
plot in the Typical Performance Curves. The noise
measurement is made with a bandpass filter made of
a 1 pole high-pass filter with a corner frequency at
.1Hz and a 2-pole low-pass filter with a corner
frequency at 12.6Hz to create a filter with a 9.9Hz
bandwidth. Noise in the 10KHz to 1MHz bandwidth is
approximately 400μVp-p with no capacitance on the
output, as shown in Fig. 2 below. These noise
measurements are made with a 2 decade bandpass
filter made of a 1 pole high-pass filter with a corner
frequency at 1/10 of the center frequency and 1-pole
low-pass filter with a corner frequency at 10 times the
center frequency. Figure 2 also shows the noise in the
10KHz to 1MHz band can be reduced to about 50μVp-
p using a .001μF capacitor on the output. Noise in the
1KHz to 100KHz band can be further reduced using a
0.1μF capacitor on the output, but noise in the 1Hz to
100Hz band increases due to instability of the very low
power amplifier with a 0.1μF capacitance load. For
V
IN
= 4.5V to 6.5V
0.001μF
Serial
Bus
V
IN
V
OUT
X60008-25
GND
REF IN
Enable
SCK
SDAT
12 to 24-bit
A/D Converter
0.01μF
10μF
X60008B-25
相關PDF資料 |
PDF描述 |
|---|---|
| X60008DIS8Z-25 | Precision 2.5V FGA⑩ Voltage Reference |
| X60008BIS8-41 | Precision 4.096V FGA⑩ Voltage Reference |
| X60008BIS8Z-41 | Precision 4.096V FGA⑩ Voltage Reference |
| X60008CIS8-41 | Precision 4.096V FGA⑩ Voltage Reference |
| X60008CIS8Z-41 | Precision 4.096V FGA⑩ Voltage Reference |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X60008DIS8-25T1 | 功能描述:IC VREF SERIES PREC 2.5V 8-SO RoHS:否 類別:集成電路 (IC) >> PMIC - 電壓基準 系列:FGA™ 標準包裝:1 系列:- 基準類型:串聯，精度 輸出電壓:4.5V 容差:±800µV 溫度系數:1ppm/°C 輸入電壓:13.5 V ~ 22 V 通道數:1 電流 - 陰極:- 電流 - 靜態:7mA 電流 - 輸出:10mA 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:20-LCC 供應商設備封裝:20-CLCC 包裝:管件 |
| X60008DIS8-41 | 功能描述:IC VREF SERIES PREC 4.096V 8-SO RoHS:否 類別:集成電路 (IC) >> PMIC - 電壓基準 系列:FGA™ 標準包裝:3,000 系列:- 基準類型:旁路，精度 輸出電壓:5V 容差:±0.5% 溫度系數:100ppm/°C 輸入電壓:- 通道數:1 電流 - 陰極:80µA 電流 - 靜態:- 電流 - 輸出:15mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:TO-236-3，SC-59，SOT-23-3 供應商設備封裝:SOT-23-3 包裝:帶卷 (TR) 其它名稱:LM4040CIM3-5.0MLTRLM4040CIM3-5.0MLTR-ND |
| X60008DIS8-41T1 | 功能描述:IC VREF SERIES PREC 4.096V 8-SO RoHS:否 類別:集成電路 (IC) >> PMIC - 電壓基準 系列:FGA™ 標準包裝:3,000 系列:- 基準類型:旁路，精度 輸出電壓:5V 容差:±0.5% 溫度系數:100ppm/°C 輸入電壓:- 通道數:1 電流 - 陰極:80µA 電流 - 靜態:- 電流 - 輸出:15mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:TO-236-3，SC-59，SOT-23-3 供應商設備封裝:SOT-23-3 包裝:帶卷 (TR) 其它名稱:LM4040CIM3-5.0MLTRLM4040CIM3-5.0MLTR-ND |
| X60008DIS8-50 | 功能描述:IC VREF SERIES PREC 5V 8-SO RoHS:否 類別:集成電路 (IC) >> PMIC - 電壓基準 系列:FGA™ 標準包裝:1 系列:- 基準類型:串聯，精度 輸出電壓:4.5V 容差:±800µV 溫度系數:1ppm/°C 輸入電壓:13.5 V ~ 22 V 通道數:1 電流 - 陰極:- 電流 - 靜態:7mA 電流 - 輸出:10mA 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:20-LCC 供應商設備封裝:20-CLCC 包裝:管件 |
| X60008DIS8-50T1 | 功能描述:IC VREF SERIES PREC 5V 8-SO RoHS:否 類別:集成電路 (IC) >> PMIC - 電壓基準 系列:FGA™ 標準包裝:3,000 系列:- 基準類型:旁路，精度 輸出電壓:5V 容差:±0.5% 溫度系數:100ppm/°C 輸入電壓:- 通道數:1 電流 - 陰極:80µA 電流 - 靜態:- 電流 - 輸出:15mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:TO-236-3，SC-59，SOT-23-3 供應商設備封裝:SOT-23-3 包裝:帶卷 (TR) 其它名稱:LM4040CIM3-5.0MLTRLM4040CIM3-5.0MLTR-ND |
發布緊急采購，3分鐘左右您將得到回復。