參數資料
型號: X5163V14I-2.7
廠商: INTERSIL CORP
元件分類: 電源管理
英文描述: RTC Module With CPU Supervisor
中文描述: 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO14
封裝: PLASTIC, MO-153AC, TSSOP-14
文件頁數: 2/21頁
文件大?。?/td> 117K
代理商: X5163V14I-2.7
X5163/X5165 – Preliminary Information
Characteristics subject to change without notice.
2 of 21
REV 1.1 3/5/01
www.xicor.com
PIN DESCRIPTION
PIN CONFIGURATION
Pin
(SOIC/PDIP)
1
Pin
TSSOP
1
Name
CS/WDI
Function
Chip Select Input.
a high impedance state. Unless a nonvolatile write cycle is underway, the device
will be in the standby power mode. CS LOW enables the device, placing it in the
active power mode. Prior to the start of any operation after power up, a HIGH to
LOW transition on CS is required
Watchdog Input.
A HIGH to LOW transition on the WDI pin restarts the Watch-
dog timer. The absence of a HIGH to LOW transition within the watchdog time
out period results in RESET/RESET going active.
Serial Output.
SO is a push/pull serial data output pin. A read cycle shifts data out
on this pin. The falling edge of the serial clock (SCK) clocks the data out.
Write Protect.
The WP pin works in conjunction with a nonvolatile WPEN bit to
“l(fā)ock” the setting of the Watchdog Timer control and the memory write protect bits.
Ground
Serial Input.
SI is a serial data input pin. Input all opcodes, byte addresses, and
memory data on this pin. The rising edge of the serial clock (SCK) latches the input
data. Send all opcodes (Table 1), addresses and data MSB first.
Serial Clock.
The Serial Clock controls the serial bus timing for data input and out-
put. The rising edge of SCK latches in the opcode, address, or data bits present on
the SI pin. The falling edge of SCK changes the data output on the SO pin.
Reset Output
.
RESET/RESET is an active LOW/HIGH, open drain output which
goes active whenever V
CC
falls below the minimum V
active until V
CC
rises above the minimum V
RESET goes active if the Watchdog Timer is enabled and CS remains either
HIGH or LOW longer than the selectable Watchdog time out period. A falling
edge of CS will reset the Watchdog Timer. RESET/RESET goes active on power
up at 1V and remains active for 200ms after the power supply stabilizes.
Supply Voltage
No internal connections
CS HIGH, deselects the device and the SO output pin is at
2
2
SO
3
6
WP
4
5
7
8
V
SS
SI
6
9
SCK
7
13
RESET/
RESET
CC
sense level. It will remain
sense level for 200ms. RESET/
CC
8
14
V
NC
CC
3-5,10-
12
8-Lead SOIC/PDIP
CS/WDI
WP
SO
1
2
3
4
RESET/RESET
8
7
6
5
V
CC
14-Lead TSSOP
SO
NC
WP
V
SS
1
2
3
4
5
6
7
RESET/RESET
SCK
SI
14
13
12
11
10
9
8
V
CC
NC
X5163/65
V
SS
SCK
CS/WDI
NC
NC
NC
NC
X5163/65
SI
相關PDF資料
PDF描述
X5163V14I-2.7A RTC Module With CPU Supervisor
X5163V14I-2.7T1 RTC Module With CPU Supervisor
X5163V14I-4.5A RTC Module With CPU Supervisor
X5163V14T1 RTC Module With CPU Supervisor
X5165 RTC Module With CPU Supervisor
相關代理商/技術參數
參數描述
X5163V14I-4.5A 功能描述:IC SUPERVISOR CPU 16K EE 14TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:推挽式,圖騰柱 復位:低有效 復位超時:最小 145 ms 電壓 - 閥值:2.64V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WQFN 裸露焊盤 供應商設備封裝:16-TQFN-EP(4x4) 包裝:帶卷 (TR)
X5163V14IT1 功能描述:IC SUPERVISOR CPU 16K EE 14TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:推挽式,圖騰柱 復位:低有效 復位超時:最小 145 ms 電壓 - 閥值:2.64V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WQFN 裸露焊盤 供應商設備封裝:16-TQFN-EP(4x4) 包裝:帶卷 (TR)
X5163V14IZ 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CPU Supervisor with 16Kbit SPI EEPROM
X5163V14IZ-2.7 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CPU Supervisor with 16Kbit SPI EEPROM
X5163V14IZ-2.7A 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CPU Supervisor with 16Kbit SPI EEPROM