參數資料
型號： X51638V14
英文描述： IN SAWN WAFER 20 MIL(MCU AVR)
中文描述： SPI串行EEPROM，帶有監控功能
文件頁數： 5/21頁
文件大?。?/td> 117K
代理商： X51638V14
X5163/X5165 – Preliminary Information
Characteristics subject to change without notice.
5 of 21
REV 1.1 3/5/01
www.xicor.com
Figure 4. Sample V
TRIP
Reset Circuit
1
2
3
4
8
7
6
5
X5163/65
V
TRIP
Adj.
Program
NC
NC
V
P
Reset V
TRIP
Test
V
TRIP
Set V
TRIP
NC
RESET
4.7K
4.7K
10K
10K
+
SPI SERIAL MEMORY
The memory portion of the device is a CMOS Serial
EEPROM array with Xicor’s block lock protection. The
array is internally organized as x 8. The device features
a Serial Peripheral Interface (SPI) and software proto-
col allowing operation on a simple four-wire bus.
The device utilizes Xicor’s proprietary Direct Write
cell, providing a minimum endurance of 100,000 cycles
and a minimum data retention of 100 years.
The device is designed to interface directly with the
synchronous Serial Peripheral Interface (SPI) of many
popular microcontroller families. It contains an 8-bit
instruction register that is accessed via the SI input,
with data being clocked in on the rising edge of SCK.
CS must be LOW during the entire operation.
All instructions (Table 1), addresses and data are
transferred MSB first. Data input on the SI line is
latched on the first rising edge of SCK after CS goes
LOW. Data is output on the SO line by the falling edge
of SCK. SCK is static, allowing the user to stop the
clock and then start it again to resume operations
where left off.
Write Enable Latch
The device contains a Write Enable Latch. This latch
must be SET before a Write Operation is initiated. The
WREN instruction will set the latch and the WRDI
instruction will reset the latch (Figure 3). This latch is
automatically reset upon a power-up condition and
after the completion of a valid Write Cycle.
Status Register
The RDSR instruction provides access to the Status
Register. The Status Register may be read at any time,
even during a Write Cycle. The Status Register is for-
matted as follows:
The Write-In-Progress (WIP) bit is a volatile, read only
bit and indicates whether the device is busy with an
internal nonvolatile write operation. The WIP bit is read
using the RDSR instruction. When set to a “1”, a non-
volatile write operation is in progress. When set to a
“0”, no write is in progress.
7
6
5
4
3
2
1
0
WPEN
FLB
WD1
WD0
BL1
BL0
WEL
WIP
相關PDF資料
PDF描述
X51638V14-1.8 1.8V, 10MHZ, PDIP, IND TEMP(MCU AVR)
X51638V14-2.7 U.8V,10MHZ, NARROW SOIC, IND TEMP, GREEN(MCU AVR)
X51638V14-2.7A SPI Serial EEPROM with Supervisory Features
X5163S8I-4.5A RTC Module With CPU Supervisor
X5165S8-2.7 RTC Module With CPU Supervisor
相關代理商/技術參數
參數描述
X51638V14-1.8 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SPI Serial EEPROM with Supervisory Features
X51638V14-2.7 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SPI Serial EEPROM with Supervisory Features
X51638V14-2.7A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SPI Serial EEPROM with Supervisory Features
X5163P 功能描述:IC CPU SUPRV 16K EE RST LO 8DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:低有效 復位超時:標準傳輸延遲為 60 µs 電壓 - 閥值:3V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:Digi-Reel® 其它名稱:LM8364BALMF30DKR
X5163P-2.7 功能描述:IC SUPERVISOR CPU 16K EE 8-DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:推挽式，圖騰柱 復位:低有效 復位超時:最小 145 ms 電壓 - 閥值:2.64V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WQFN 裸露焊盤 供應商設備封裝:16-TQFN-EP（4x4） 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*