- 您現在的位置：買賣IC網 > PDF目錄371263 > X51638S8I-2.7A SPI Serial EEPROM with Supervisory Features PDF資料下載
參數資料
| 型號： | X51638S8I-2.7A |
| 元件分類： | EEPROM |
| 英文描述： | SPI Serial EEPROM with Supervisory Features |
| 中文描述： | SPI串行EEPROM，帶有監控功能 |
| 文件頁數： | 3/21頁 |
| 文件大小： | 117K |
| 代理商： | X51638S8I-2.7A |
X5163/X5165 – Preliminary Information
Characteristics subject to change without notice.
3 of 21
REV 1.1 3/5/01
www.xicor.com
PRINCIPLES OF OPERATION
Power On Reset
Application of power to the X5163/X5165 activates a
Power On Reset Circuit. This circuit goes active at 1V
and pulls the RESET/RESET pin active. This signal
prevents the system microprocessor from starting to
operate with insufficient voltage or prior to stabilization
of the oscillator. When V
CC
value for 200ms (nominal) the circuit releases RESET/
RESET, allowing the processor to begin executing code.
exceeds the device V
TRIP
Low Voltage Monitoring
During operation, the X5163/X5165 monitors the V
level and asserts RESET/RESET if supply voltage falls
below a preset minimum V
signal prevents the microprocessor from operating in a
power fail or brownout condition. The RESET/RESET
signal remains active until the voltage drops below 1V.
It also remains active until V
V
TRIP
for 200ms.
CC
TRIP
. The RESET/RESET
CC
returns and exceeds
Watchdog Timer
The Watchdog Timer circuit monitors the microproces-
sor activity by monitoring the WDI input. The micropro-
cessor must toggle the CS/WDI pin periodically to
prevent a RESET/RESET signal. The CS/WDI pin
must be toggled from HIGH to LOW prior to the expira-
tion of the watchdog time out period. The state of two
nonvolatile control bits in the Status Register deter-
mine the watchdog timer period. The microprocessor
can change these watchdog bits, or they may be
“l(fā)ocked” by tying the WP pin LOW and setting the
WPEN bit HIGH.
V
The X5163/X5165 has a standard V
(V
TRIP
) voltage. This value will not change over normal
operating and storage conditions. However, in applica-
tions where the standard V
for higher precision in the V
X5165 threshold may be adjusted.
CC
Threshold Reset Procedure
CC
threshold
TRIP
is not exactly right, or
value, the X5163/
TRIP
Setting the V
This procedure sets the V
value. For example, if the current V
new V
TRIP
is 4.6V, this procedure directly makes the
change. If the new setting is lower than the current set-
ting, then it is necessary to reset the trip point before
setting the new value.
TRIP
Voltage
TRIP
to a higher voltage
is 4.4V and the
TRIP
To set the new V
threshold to the V
the WP pin HIGH. RESET and SO pins are left uncon-
nected. Then apply the programming voltage V
both SCK and SI and pulse CS/WDI LOW then HIGH.
Remove V
P
and the sequence is complete.
TRIP
CC
voltage, apply the desired V
pin and tie the CS/WDI pin and
TRIP
P
to
Figure 1. Set V
TRIP
Voltage
Resetting the V
This procedure sets the V
level. For example, if the current V
V
TRIP
is reset, the new V
1.7V. This procedure must be used to set the voltage to
a lower value.
TRIP
Voltage
TRIP
to a “native” voltage
is 4.4V and the
is something less than
TRIP
TRIP
To reset the V
2.7 and 5.5V to the V
WP pin, AND THE SCK pin HIGH. RESET and SO
pins are left unconnected. Then apply the program-
ming voltage V
P
to the SI pin ONLY and pulse CS/WDI
LOW then HIGH. Remove V
complete.
TRIP
voltage, apply a voltage between
pin. Tie the CS/WDI pin, the
CC
P
and the sequence is
Figure 2. Reset V
TRIP
Voltage
SCK
SI
V
P
V
P
CS
SCK
SI
V
CC
V
P
CS
相關PDF資料 |
PDF描述 |
|---|---|
| X51638S8I-4.5A | 5V, 20MHZ, SOIC, IND TEMP(MCU AVR) |
| X51638V14 | IN SAWN WAFER 20 MIL(MCU AVR) |
| X51638V14-1.8 | 1.8V, 10MHZ, PDIP, IND TEMP(MCU AVR) |
| X51638V14-2.7 | U.8V,10MHZ, NARROW SOIC, IND TEMP, GREEN(MCU AVR) |
| X51638V14-2.7A | SPI Serial EEPROM with Supervisory Features |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X51638S8I-4.5A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SPI Serial EEPROM with Supervisory Features |
| X51638V14 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SPI Serial EEPROM with Supervisory Features |
| X51638V14-1.8 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SPI Serial EEPROM with Supervisory Features |
| X51638V14-2.7 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SPI Serial EEPROM with Supervisory Features |
| X51638V14-2.7A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SPI Serial EEPROM with Supervisory Features |
發布緊急采購，3分鐘左右您將得到回復。