- 您現在的位置：買賣IC網 > PDF目錄371259 > X5001V8-4.5A (INTERSIL CORP) RTC Module With CPU Supervisor PDF資料下載
參數資料
| 型號： | X5001V8-4.5A |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | RTC Module With CPU Supervisor |
| 中文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| 封裝： | PLASTIC, TSSOP-8 |
| 文件頁數： | 3/19頁 |
| 文件大?。?/td> | 100K |
| 代理商： | X5001V8-4.5A |
X5001
3
PRINCIPLES OF OPERATION
Power On Reset
Application of power to the X5001 activates a Power On
Reset Circuit. This circuit goes active at 1V and pulls the
RESET/RESET pin active. This signal prevents the sys-
tem microprocessor from starting to operate with insuffi-
cient voltage or prior to stabilization of the oscillator. When
Vcc exceeds the device V
TRIP
the circuit releases RESET, allowing the processor to
begin executing code.
value for 200ms (nominal)
Low voltage monitoring
During operation, the X5001 monitors the V
asserts RESET if supply voltage falls below a preset mini-
mum V
TRIP
. The RESET signal prevents the microproces-
sor from operating in a power fail or brownout condition.
The RESET signal remains active until the voltage drops
below 1V. It also remains active until Vcc returns and
exceeds V
TRIP
for 200ms.
CC
level and
watchdog timer
The Watchdog Timer circuit monitors the microprocessor
activity by monitoring the WDI input. The microprocessor
must toggle the CS/WDI pin periodically to prevent a
RESET signal. The CS/WDI pin must be toggled from
HIGH to LOW prior to the expiration of the watchdog time-
out period. The state of two nonvolatile control bits in the
Watchdog Register determine the watchdog timer period.
Vcc Threshold Reset Procedure
The X5001 is shipped with a standard Vcc threshold
(V
TRIP
) voltage. This value will not change over normal
operating and storage conditions. However, in applica-
tions where the standard V
TRIP
higher precision is needed in the V
threshold may be adjusted. The procedure is described
below, and requires the application of a high voltage con-
trol signal.
is not exactly right, or if
TRIP
value, the X5001
Setting the V
This procedure is used to set the V
age value. For example, if the current V
the new V
TRIP
is 4.6V, this procedure will directly make
the change. If the new setting is to be lower than the cur-
rent setting, then it is necessary to reset the trip point
before setting the new value.
TRIP
Voltage
TRIP
to a higher volt-
TRIP
is 4.4V and
To set the new V
threshold voltage to the Vcc pin and tie the W
programming voltage V
command sequence is sent to the device over the SPI
interface. This V
TRIP
programming sequence consists of
pulling CS LOW, then clocking in data 03h, 00h and 01h.
This is followed by bringing CS HIGH then LOW and
clocking in data 02h, 00h, and 01h (in order) and bringing
CS HIGH. This initiates the V
sequence. V
P
is brought LOW to end the operation.
TRIP
voltage, apply the desired V
TRIP
PE
pin to the
P
. Then a V
TRIP
programming
TRIP
programming
Resetting the V
This procedure is used to set the V
age level. For example, if the current V
the new V
TRIP
must be 4.0V, then the V
reset. When V
TRIP
is reset, the new V
less than 1.7V. This procedure must be used to set the
voltage to a lower value.
TRIP
Voltage
TRIP
to a “native” volt-
TRIP
is 4.4V and
TRIP
must be
TRIP
is something
To reset the V
Vcc pin and tie the W
Vp. Then a V
device over the SPI interface. This V
sequence consists of pulling CS LOW, then clocking in
data 03h, 00h and 01h. This is followed by bringing CS
HIGH then LOW and clocking in data 02h, 00h, and 03h
(in order) and bringing CS HIGH. This initiates the V
programming sequence. V
P
is brought LOW to end the
operation.
TRIP
voltage, apply greater than 3V to the
PE
pin to the programming voltage
TRIP
command sequence is sent to the
TRIP
programming
TRIP
相關PDF資料 |
PDF描述 |
|---|---|
| X5001 | RTC Module With CPU Supervisor |
| X5001P | RTC Module With CPU Supervisor |
| X5001S8 | RTC Module With CPU Supervisor |
| X5001S8-2.7 | RTC Module With CPU Supervisor |
| X5001S8-2.7A | RTC Module With CPU Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X5001V8I | 功能描述:IC SUPERVISOR CPU 8-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:推挽式，圖騰柱 復位:低有效 復位超時:最小 145 ms 電壓 - 閥值:2.64V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WQFN 裸露焊盤 供應商設備封裝:16-TQFN-EP（4x4） 包裝:帶卷 (TR) |
| X5001V8I-2.7 | 功能描述:IC SUPERVISOR CPU 8-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:推挽式，圖騰柱 復位:低有效 復位超時:最小 145 ms 電壓 - 閥值:2.64V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WQFN 裸露焊盤 供應商設備封裝:16-TQFN-EP（4x4） 包裝:帶卷 (TR) |
| X5001V8I-2.7A | 功能描述:IC SUPERVISOR CPU 8-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:推挽式，圖騰柱 復位:低有效 復位超時:最小 145 ms 電壓 - 閥值:2.64V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WQFN 裸露焊盤 供應商設備封裝:16-TQFN-EP（4x4） 包裝:帶卷 (TR) |
| X5001V8I-4.5A | 功能描述:IC SUPERVISOR CPU 8-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:推挽式，圖騰柱 復位:低有效 復位超時:最小 145 ms 電壓 - 閥值:2.64V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WQFN 裸露焊盤 供應商設備封裝:16-TQFN-EP（4x4） 包裝:帶卷 (TR) |
| X5001V8IZ-2.7 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CPU Supervisor |
發布緊急采購，3分鐘左右您將得到回復。