- 您現在的位置：買賣IC網 > PDF目錄376443 > X4325V8I-4.5A (INTERSIL CORP) RTC Module With CPU Supervisor PDF資料下載
參數資料
| 型號： | X4325V8I-4.5A |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | RTC Module With CPU Supervisor |
| 中文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| 封裝： | 4.40 MM, PLASTIC, MO-153AC, TSSOP-8 |
| 文件頁數： | 8/21頁 |
| 文件大?。?/td> | 333K |
| 代理商： | X4325V8I-4.5A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁
8
FN8122.0
March 29, 2005
Serial Start Condition
All commands are preceded by the start condition,
which is a HIGH to LOW transition of SDA when SCL
is HIGH. The device continuously monitors the SDA
and SCL lines for the start condition and will not
respond to any command until this condition has been
met. See Figure 6.
Serial Stop Condition
All communications must be terminated by a stop con-
dition, which is a LOW to HIGH transition of SDA when
SCL is HIGH. The stop condition is also used to place
the device into the Standby power mode after a read
sequence. A stop condition can only be issued after the
transmitting device has released the bus. See Figure 6.
Figure 6. Valid Start and Stop Conditions
Serial Acknowledge
Acknowledge is a software convention used to indi-
cate successful data transfer. The transmitting device,
either master or slave, will release the bus after trans-
mitting eight bits. During the ninth clock cycle, the
receiver will pull the SDA line LOW to acknowledge
that it received the eight bits of data. Refer to Figure 7.
The device will respond with an acknowledge after
recognition of a start condition and if the correct
Device Identifier and Select bits are contained in the
Slave Address Byte. If a write operation is selected,
the device will respond with an acknowledge after the
receipt of each subsequent eight bit word. The device
will acknowledge all incoming data and address bytes,
except for the Slave Address Byte when the Device
Identifier and/or Select bits are incorrect.
In the read mode, the device will transmit eight bits of
data, release the SDA line, then monitor the line for an
acknowledge. If an acknowledge is detected and no
stop condition is generated by the master, the device
will continue to transmit data. The device will terminate
further data transmissions if an acknowledge is not
detected. The master must then issue a stop condition
to return the device to Standby mode and place the
device into a known state.
Figure 7. Acknowledge Response From Receiver
SCL
SDA
Start
Stop
Data Output
from
Data Output
from Receiver
8
1
9
Start
Acknowledge
SCL from
Master
X4323, X4325
相關PDF資料 |
PDF描述 |
|---|---|
| X4C105 | RTC Module With CPU Supervisor |
| X4C105V20I | RTC Module With CPU Supervisor |
| X5329V14Z-4.5A | RTC Module With CPU Supervisor |
| X5648P-4.5A | CAP 270PF 50V CERAMIC MONO 5% |
| X5648 | Thyristor Module |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X-4328-TT-R | 功能描述:音頻指示器及警報器 9VDC 12MA 108DBA 2800HZ RoHS:否 制造商:PUI Audio 產品:Indicators 聲壓級:85 dB 音調:Continuous 頻率:2300 Hz +/- 300 Hz 電壓額定值:5 VDC 電流額定值:30 mA 端接類型: 直徑:12 mm 安裝:Through Hole |
| X433-133.33M | 制造商:CONNOR-WINFIELD 制造商全稱:Connor-Winfield Corporation 功能描述:5.0x7.0mm Surface Mount LVCMOS Clock Oscillator Series |
| X4350PSF1 | 制造商:ABB Low Voltage Products and Systems 功能描述:CCT,350VA,460V/120V SINGLE |
| X436 | 制造商:Heyco Products Inc 功能描述: |
| X-439289A | 制造商:Volex Group 功能描述:LEAD 5A BLACK 3M |
發布緊急采購，3分鐘左右您將得到回復。