- 您現在的位置：買賣IC網 > PDF目錄372534 > X4165V8I-2.7 (INTERSIL CORP) CPU Supervisor with 16K EEPROM PDF資料下載
參數資料
| 型號： | X4165V8I-2.7 |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | CPU Supervisor with 16K EEPROM |
| 中文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| 封裝： | PLASTIC, MO-153AC, TSSOP-8 |
| 文件頁數： | 6/23頁 |
| 文件大?。?/td> | 118K |
| 代理商： | X4165V8I-2.7 |
X46402
Characteristics subject to change without notice.
6 of 23
Figure 5. Reset V2
TRIP
Level Sequence (V
CC
> 3V, WEL is set.)
SDA
D8h
00h
RESET
V
P
= 15V
V2
TRIP
V2MON
0Fh
0Fh resets V2MON
SCL
0
1
2 3
4
5 6
7
0 1
2 3
4
5 6
7
0 1
2 3
4
5 6
7
0 1
2 3
4
5 6
7
00h
V
CC
The X46402 is shipped with standard V
V2
TRIP
voltages. These values will not change over
normal operating and storage conditions. However, in
applications where the standard thresholds are not
exactly right, or if higher precision is needed in the
threshold value, the X46402 trip points may be
adjusted. The procedure is described below, and uses
the application of a high voltage control signal.
AND V2MON THRESHOLD RESET PROCEDURE
TRIP,
and
Setting the V
This procedure is used to set the V
lower or higher voltage value. It is necessary to reset
the trip point before setting the new value.
TRIP
Voltage
TRIP
,V2
TRIP
to a
To set the new voltages, apply the desired V
threshold voltage to the V
the V2MON pin, then tie the RESET pin to the pro-
gramming voltage V
P
. Then, write 4 byte to program
TRIP
CC
pin, the V2
TRIP
voltage to
V
valid write operation initiates the programming sequence.
Bring RESET
LOW to complete the operation.
TRIP
, V2
TRIP
respectively. The stop bit following a
Resetting the V
This procedure is used to set the V
a “native” voltage level. For example, if the current
V
TRIP
is 4.4V and the new V
TRIP
must be 4.0V, then
the V
TRIP
must be reset. When the threshold is reset,
the new level is something less than 1.7V. This proce-
dure must be used to set the voltage to a lower value.
TRIP
Voltage
TRIP
, the V2
TRIP
to
To reset the new V
TRIP
, V2
TRIP
voltage, apply the
desired V
TRIP
or V2
TRIP
threshold voltage to the V
CC
or V2MON pin, respectively, and tie the RESET pin to
the programming voltage V
P
. Then write 4 byte
address. The stop bit of a valid write operation initiates
the programming sequence. Bring RESET
LOW to
complete the operation.
Figure 6. Sample V
TRIP
Reset Circuit
5
4
7
1
8
2
6
3
X46402
V
TRIP
Adj.
V
P
RESET
4.7K
SDA
SCL
μC
Adjust
Run
V2FAIL
V2
TRIP
Adj.
相關PDF資料 |
PDF描述 |
|---|---|
| X4283(中文) | RTC Module With CPU Supervisor |
| X4283 | RTC Module With CPU Supervisor |
| X4323 | RTC Module With CPU Supervisor |
| X4325 | RTC Module With CPU Supervisor |
| X4643(中文) | RTC Module With CPU Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X4165V8I-4.5A | 功能描述:IC SUPERVISOR CPU 16K EE 8-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X41D255 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| X41K1 | 制造商:ABB Low Voltage Products and Systems 功能描述:CCT,1KVA,460V,SINGLE |
| X41K403 | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Harris Corporation 功能描述: |
| X41K417 | 制造商:Harris Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。