- 您現在的位置：買賣IC網 > PDF目錄371254 > X4043 (Intersil Corporation) RTC Module With CPU Supervisor PDF資料下載
參數資料
| 型號： | X4043 |
| 廠商： | Intersil Corporation |
| 元件分類： | CPU監測 |
| 英文描述： | RTC Module With CPU Supervisor |
| 中文描述： | 時鐘模塊CPU監控 |
| 文件頁數： | 6/25頁 |
| 文件大?。?/td> | 144K |
| 代理商： | X4043 |
X4043/45
Characteristics subject to change without notice.
6 of 25
REV 1.1.17 9/14/01
www.xicor.com
Figure 5. V
TRIP
Programming Sequence
V
TRIP
Programming
Power Down
the Device
Actual V
TRIP
–
Desired V
TRIP
= Error
DONE
Set Higher V
TRIP
Sequence
Error < MDE
–
| Error | < | MDE |
YES
NO
Error > MDE
+
Desired
V
TRIP
<
Present Value
Execute
No
YES
Execute
V
TRIP
Reset Sequence
Set V
CC
= desired V
TRIP
New V
CC
applied =
Old V
CC
applied + | Error |
New V
CC
applied =
Old V
CC
applied – | Error |
Execute Reset V
TRIP
Sequence
Output Switches
(RESET)
Let:
MDE = Maximum Desired Error
MDE
+
Desired Value
MDE
–
Acceptable
Error Range
Error = Actual – Desired
Ramp V
CC
Control Register
The control register provides the user a mechanism for
changing the block lock and watchdog timer settings.
The block lock and watchdog timer bits are nonvolatile
and do not change when power is removed.
The control register is accessed with a special pream-
ble in the slave byte (1011) and is located at address
1FFh. It can only be modified by performing a byte
write operation directly to the address of the register
and only one data byte is allowed for each register
write operation. Prior to writing to the control register,
the WEL and RWEL bits must be set using a two step
process, with the whole sequence requiring 3 steps.
See "Writing to the Control Register".
The user must issue a stop after sending this byte to
the register to initiate the nonvolatile cycle that stores
WD1, WD0, BP2, BP1, and BP0. The X4043/45 will not
acknowledge any data bytes written after the first byte
is entered.
相關PDF資料 |
PDF描述 |
|---|---|
| X4045P | RTC Module With CPU Supervisor |
| X4045S8I-4.5A | RTC Module With CPU Supervisor |
| X4045S8IZ | RTC Module With CPU Supervisor |
| X4045S8IZ-2.7A | RTC Module With CPU Supervisor |
| X4045S8Z | RTC Module With CPU Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X4043_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CPU Supervisor with 4kbit EEPROM |
| X40430 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple Voltage Monitor with Integrated CPU Supervisor |
| X40430_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple Voltage Monitor with Integrated CPU Supervisor |
| X40430S14 | 功能描述:IC VOLT MON TRPL EEPROM 14-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X40430S14-A | 功能描述:IC VOLT MON TRPL EEPROM 14-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。