- 您現在的位置：買賣IC網 > PDF目錄371223 > X25C02MM SPI Serial E2PROM PDF資料下載
參數資料
| 型號： | X25C02MM |
| 英文描述： | SPI Serial E2PROM |
| 中文描述： | 的SPI串行E2PROM |
| 文件頁數： | 2/14頁 |
| 文件大小： | 60K |
| 代理商： | X25C02MM |
X25C02
2
PIN DESCRIPTIONS
Serial Output (SO)
SO is a push/pull serial data output pin. During a read
cycle, data is shifted out on this pin. Data is clocked out
by the falling edge of the serial clock.
Serial Input (SI)
SI is the serial data input pin. All data, opcodes, byte
addresses, and data to be written to the memory are
input on this pin. Data is latched by the rising edge of the
serial clock.
Serial Clock (SCK)
The Serial Clock controls the serial bus timing for data
input and output. Opcodes, addresses, or data present
on the SI pin are sampled or latched on the rising edge
of the clock input, while data on the SO pin change after
the falling edge of the clock input.
Chip Select (
CS
)
When
CS
is HIGH, the X25C02 is deselected and the
SO output pin is at HIGH impedance and unless an
internal write operation is underway, the X25C02 will be
in the standby power mode.
CS
LOW enables the
X25C02, placing it in the active power mode. It should be
noted that after power-up, a HIGH to LOW transition on
CS
is required prior to the start of any operation.
Write Protect (
WP
)
When
WP
is LOW, nonvolatile writes to the X25C02 are
disabled, but the part otherwise functions normally.
When
WP
is held HIGH, all functions, including nonvola-
tile writes operate normally.
WP
going LOW while
CS
is
still LOW will interrupt a write to the X25C02. If the
internal write cycle has already been initiated,
WP
going
LOW will have no affect on a write.
Hold (
HOLD
)
HOLD
is used in conjunction with the
CS
pin to select the
device. Once the part is selected and a serial sequence is
underway,
HOLD
may be used to pause the serial
communication with the controller without resetting
the serial sequence. To pause,
HOLD
must be brought
LOW while SCK is LOW. To resume communication,
HOLD
is brought HIGH, again while SCK is LOW. If the
pause feature is not used,
HOLD
should be held HIGH
at all times.
PIN CONFIGURATION
PIN NAMES
Symbol
CS
SO
SI
SCK
WP
V
SS
V
CC
HOLD
Description
Chip Select Input
Serial Output
Serial Input
Serial Clock Input
Write Protect Input
Ground
Supply Voltage
Hold Input
3843 PGM T01
3843 FHD F02.2
CS
SO
WP
VSS
1
2
3
4
8
7
6
5
VCC
HOLD
SCK
SI
X25C02
MSOP/DIP/SOIC
相關PDF資料 |
PDF描述 |
|---|---|
| X25C02P | SPI Serial E2PROM |
| X25C02PI | SPI Serial E2PROM |
| X25C02PM | SPI Serial E2PROM |
| X25C02S | SPI Serial E2PROM |
| X25C02SI | SPI Serial E2PROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X25C02P | 制造商:Intersil Corporation 功能描述: |
| X25C02P-3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SPI Serial EEPROM |
| X25C02PI | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:SPI Serial E2PROM |
| X25C02PI-3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SPI Serial EEPROM |
| X25C02PM | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:SPI Serial E2PROM |
發布緊急采購，3分鐘左右您將得到回復。