- 您現在的位置：買賣IC網 > PDF目錄371210 > X25040V-3 60V Single N-Channel HEXFET Power MOSFET in a D2-Pak package; Similar to IRFZ44ES with Lead Free Packaging PDF資料下載
參數資料
| 型號： | X25040V-3 |
| 英文描述： | 60V Single N-Channel HEXFET Power MOSFET in a D2-Pak package; Similar to IRFZ44ES with Lead Free Packaging |
| 中文描述： | SPI串行EEPROM |
| 文件頁數： | 2/13頁 |
| 文件大小： | 128K |
| 代理商： | X25040V-3 |
X25040
Characteristics subject to change without notice.
2 of 13
REV 1.1 7/12/00
www.xicor.com
FORNEWDESGNS
PIN DESCRIPTIONS
Serial Output (SO)
SO is a push/pull serial data output pin. During a read
cycle, data is shifted out on this pin. Data is clocked out
by the falling edge of the serial clock.
Serial Input (SI)
SI is the serial data input pin. All opcodes, byte
addresses, and data to be written to the memory are
input on this pin. Data is latched by the rising edge of
the serial clock.
Serial Clock (SCK)
The Serial Clock controls the serial bus timing for data
input and output. Opcodes, addresses, or data present
on the SI pin are latched on the rising edge of the clock
input, while data on the SO pin change after the falling
edge of the clock input.
Chip Select (CS)
When CS is HIGH, the X25040 is deselected, the SO
output pin is at high impedance and unless an internal
write operation is underway, the X25040 will be in the
standby power mode. CS LOW enables the X25040,
placing it in the active power mode. It should be noted
that after power-up, a HIGH to LOW transition on CS is
required prior to the start of any operation.
Write Protect (WP)
When WP is LOW, nonvolatile writes to the X25040 are
disabled, but the part otherwise functions normally.
When WP is held HIGH, all functions, including nonvol-
atile writes, operate normally. WP going LOW while CS
is still LOW will interrupt a write to the X25040. If the
internal write cycle has already been initiated, WP
going LOW will have no affect on a write.
Hold (HOLD)
HOLD is used in conjunction with the CS pin to select
the device. Once the part is selected and a serial
sequence is underway, HOLD may be used to pause
the serial communication with the controller, without
resetting the serial sequence. To pause, HOLD must
be brought LOW while SCK is LOW. To resume com-
munication, HOLD is brought HIGH, again while SCK
is LOW. If the pause feature is not used, HOLD should
be held HIGH at all times.
PIN CONFIGURATION
PIN NAMES
Symbol
CS
SO
SI
SCK
WP
V
SS
V
CC
HOLD
Description
Chip Select Input
Serial Output
Serial Input
Serial Clock Input
Write Protect Input
Ground
Supply Voltage
Hold Input
SOIC
CS
SO
WP
V
SS
V
CC
HOLD
SCK
SI
X25040
1
2
3
4
8
7
6
5
相關PDF資料 |
PDF描述 |
|---|---|
| X25040VI | SPI Serial EEPROM |
| X25040VI-2.7 | SPI Serial EEPROM |
| X25040VI-3 | 100V Single N-Channel HEXFET Power MOSFET in a TO-262 package; A IRFSL4410 with Standard Packaging |
| X25043P-3 | 100V Single N-Channel HEXFET Power MOSFET in a D2-Pak package; Similar to IRF3710S with Lead Free Packaging |
| X25043PI-3 | 100V Single N-Channel HEXFET Power MOSFET in a D2-Pak package; Similar to IRF3710STRL with Lead Free Packaging on Tape and Reel Left |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X25040VI | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SPI Serial EEPROM |
| X25040VI-2.7 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SPI Serial EEPROM |
| X25040VI-3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SPI Serial EEPROM |
| X25041 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:SPI Serial E2PROM with Block LockTM Protection |
| X25041P | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:SPI Serial E2PROM with Block LockTM Protection |
發布緊急采購，3分鐘左右您將得到回復。