參數資料
型號： X24165
元件分類： EEPROM
英文描述： Advanced 2-Wire Serial EEPROM with Block Lock Protection(寫保護引腳，可編程塊鎖定的串行EEPROM)
中文描述： 先進的2線串行EEPROM，帶有塊鎖保護（寫保護引腳，可編程塊鎖定的串行EEPROM中）
文件頁數： 9/20頁
文件大小： 142K
代理商： X24165
X24165
9
WRITE PROTECT REGISTER
The Write Protect Register (WPR) is located at the
highest address, 7FFh.
Figure 11. Write Protect Register
WPR.1 = WEL
–
Write Enable Latch (Volatile)
0 = Write enable latch reset, writes disabled
1 = Write enable latch set, writes enabled
If WEL = 0 then “no ACK” after first byte of input data.
WPR.2 = RWEL
–
Register Write Enable Latch (Volatile)
0 = Register write enable latch reset, writes dis-
abled
1 = Register write enable latch set, writes enabled
WPR.3, WPR.4 = BP0, BP1
–
Block Protect Bits (Nonvolatile)
(See Block Protect section for definition)
WPR.7 = WPEN
–
Write Protect Enable Bit (Nonvolatile)
(See Hardware Write Protect section for definition)
Writing to the Write Protect Register
The Write Protect Register is written by performing a
random write of one byte directly to address, 7FFh. If a
page write is performed starting with any address
other than 7FFh, the byte in the array at address 7FFh
will be written instead of the Write Protect Register
(assuming writes are not disabled by the block protect
register).
The state of the Write Protect Register can be read by
performing a random read at address 7FFh at any
time. If a sequential read starting at any other address
than 7FFh is performed, the contents of the byte in the
array at 7FFh is read out instead of the Write Protect
Register.
7
6
5
4
3
2
1
0
WPEN
0
0
BP1
BP0
RWEL
WEL
0
6551 ILL F15.1
WPR (Addr = 7FFh)
WEL and RWEL are volatile latches that power-up in
the LOW (disabled) state. A write to any address other
than 7FFh, where the Write Protect Register is
located, will be ignored (no ack) until the WEL bit is set
HIGH. The WEL bit is set by writing 0000001x to
address 7FFh. Once set, WEL remains HIGH until
either reset (by writing 00000000 to 7FFh) or until the
part powers-up again. The RWEL bit controls writes to
the block protect bits. RWEL is set by first setting WEL
= 1 and then writing 0000011x to address 7FFh.
RWEL must be set in order to change the block protect
bits, BP0 and BP1, or the WPEN bit. RWEL is reset
when the block protect or WPEN bits are changed, or
when the part powers-up again.
Programming the BP or WPEN Bits
A three step sequence is required to change the
nonvoltaile Block Protect or Write Protect Enable:
1) Set WEL = 1 (write 00000010 to address 7FFh,
volatile write cycle)
(Start)
2) Set RWEL = 1 (write 00000110 to address 7FFh,
volatile write cycle)
(Start)
3) Set BP1, BP0, and/or WPEN bits (Write w00yz010
to address 7FFh)
w = WPEN, y = BP1, Z = BP0,
(Stop)
Step 3 is a nonvolatile write cycle, requiring 10ms to
complete. RWEL is reset (0) by this write cycle,
requiring another write cycle to set RWEL again before
the block protect bits can be changed. RWEL must be
0 in step 3; if w00yz110 is written to address 7FFh,
RWEL is set but WPEN, BP1 and BP0 are not
changed (the device remains at step 2).
相關PDF資料
PDF描述
X2444DM 40V Single N-Channel HEXFET Power MOSFET in a D2-Pak package; Similar to IRF2204S with Lead Free Packaging
X24C01A Serial EEPROM(二線接口串行EEPROM)
X24C01 Serial EEPROM(二線接口串行EEPROM(128×8))
X24C02(中文) Serial EEPROM(寫保護引腳,串行EEPROM)
X24C02 Serial EEPROM(寫保護引腳,串行EEPROM)
相關代理商/技術參數
參數描述
X24165F 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:Advanced 2-Wire Serial E2PROM with Block LockTM Protection
X24165FG 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:Advanced 2-Wire Serial E2PROM with Block LockTM Protection
X24165FP 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:Advanced 2-Wire Serial E2PROM with Block LockTM Protection
X24165FV 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:Advanced 2-Wire Serial E2PROM with Block LockTM Protection
X24165G 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:Advanced 2-Wire Serial E2PROM with Block LockTM Protection
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*