- 您現在的位置：買賣IC網 > PDF目錄371193 > X20C16J-45 High Speed AUTOSTORE⑩ NOVRAM PDF資料下載
參數資料
| 型號： | X20C16J-45 |
| 英文描述： | High Speed AUTOSTORE⑩ NOVRAM |
| 中文描述： | 高速自動存儲⑩NOVRAM |
| 文件頁數： | 3/21頁 |
| 文件大?。?/td> | 94K |
| 代理商： | X20C16J-45 |
X20C16
3
DEVICE OPERATION
The
CE
,
OE
,
WE,
and
NE
inputs control the X20C16
operation. The X20C16 byte-wide NOVRAM uses a
2-line control architecture to eliminate bus contention in
a system environment. The I/O bus will be in a high
impedance state when either
OE
or
CE
is HIGH, or
when
NE
is LOW.
RAM Operations
RAM read and write operations are performed as they
would be with any static RAM. A read operation requires
CE
and
OE
to be LOW with
WE
and
NE
HIGH. A write
operation requires
CE
and
WE
to be LOW with
NE
HIGH. There is no limit to the number of read or write
operations performed to the RAM portion of the X20C16.
Memory Transfer Operations
There are two memory transfer operations: a recall
operation whereby the data stored in the E
2
PROM array
is transferred to the RAM array; and a store operation
which causes the entire contents of the RAM array to be
stored in the E
2
PROM array.
Recall operations are performed automatically upon
power-up and under host system control when
NE
,
OE
and
CE
are LOW and
WE
is HIGH. The recall operation
takes a maximum of 5
μ
s.
SDP (Software Data Protection)
There are two methods of initiating a store operation.
The first is the software store command. This command
takes the place of the hardware store employed on the
X20C04. This command is issued by entering into the
special command mode:
NE
,
CE,
and
WE
strobe LOW
while at the same time a specific address and data
combination is sent to the device. This is a three step
operation: the first address/data combination is 555[H]/
AA[H]; the second combination is 2AA[H]/55[H]; and the
final command combination is 555[H]/33[H]. This se-
quence of pseudo write operations will immediately
initiate a store operation. Refer to the software com-
mand timing diagrams for details on set and hold times
for the various signals.
The second method of storing data is with the
AUTOSTORE command. When enabled, data is auto-
matically stored from the RAM into the E
2
PROM array
whenever V
CC
falls below the preset Autostore thresh-
old. This feature is enabled by performing the first two
steps for the software store with the command combina-
tion being 555[H]/CC[H].
The AUTOSTORE feature is disabled by issuing the
three step command sequence with the command com-
bination being 555[H]/CD[H]. The AUTOSTORE feature
will also be reset if V
CC
falls below the power-up reset
threshold (approximately 3.5V) and is then raised back
into the operation range.
Write Protection
The X20C16 supports two methods of protecting the
nonvolatile data.
—If after power-up the AUTOSTORE feature is not
enabled, no AUTOSTORE can occur.
—V
CC
Sense – All functions are inhibited when V
CC
is
≤
3.0V typical.
SYMBOL TABLE
The following symbol table provides a key to under-
standing the conventions used in the device timing
diagrams. The diagrams should be used in conjunction
with the device timing specifications to determine actual
device operation and performance, as well as device
suitability for user’s application.
WAVEFORM
INPUTS
OUTPUTS
Must be
steady
Will be
steady
May change
from LOW
to HIGH
Will change
from LOW
to HIGH
May change
from HIGH
to LOW
Will change
from HIGH
to LOW
Don’t Care:
Changes
Allowed
N/A
Changing:
State Not
Known
Center Line
is High
Impedance
相關PDF資料 |
PDF描述 |
|---|---|
| X20C16J-55 | ECONOLINE: RSS & RSD - 1kVDC and 3KVDC Isolation- Internal SMD Construction- UL94V-0 Package Material- Toroidal Magnetics- Efficiency to 85%- SMD5, SMD8, SMD10 and SMD12 case styles |
| X20C16JMB-55 | High Speed AUTOSTORE⑩ NOVRAM |
| X20C16D-35 | High Speed AUTOSTORE⑩ NOVRAM |
| X20C16D-45 | High Speed AUTOSTORE⑩ NOVRAM |
| X20C16D-55 | High Speed AUTOSTORE⑩ NOVRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X20C16J-55 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:High Speed AUTOSTORE⑩ NOVRAM |
| X20C16JI-35 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:High Speed AUTOSTORE⑩ NOVRAM |
| X20C16JI-45 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:High Speed AUTOSTORE⑩ NOVRAM |
| X20C16JI-55 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:High Speed AUTOSTORE⑩ NOVRAM |
| X20C16JM-35 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:High Speed AUTOSTORE⑩ NOVRAM |
發布緊急采購，3分鐘左右您將得到回復。