- 您現在的位置：買賣IC網 > PDF目錄9332 > X1288V14Z-4.5A (Intersil)IC RTC/CAL/CPU SUP EE 14-TSSOP PDF資料下載
參數資料
| 型號： | X1288V14Z-4.5A |
| 廠商： | Intersil |
| 文件頁數： | 14/27頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC RTC/CAL/CPU SUP EE 14-TSSOP |
| 標準包裝： | 95 |
| 類型： | 時鐘/日歷 |
| 特點： | 警報器，閏年，監控器，監視計時器 |
| 時間格式： | HH:MM:SS:hh（12/24 小時） |
| 數據格式： | YY-MM-DD-dd |
| 接口： | I²C，2 線串口 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 電壓 - 電源，電池： | 1.8 V ~ 5.5 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 14-TSSOP |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
21
FN8102.3
April 14, 2006
It should be noted that the ninth clock cycle of the read
operation is not a “don’t care.” To terminate a read
operation, the master must either issue a stop condi-
tion during the ninth cycle or hold SDA HIGH during
the ninth clock cycle and then issue a stop condition.
Random Read
Random read operations allows the master to access
any location in the X1288. Prior to issuing the Slave
Address Byte with the R/W bit set to zero, the master
must first perform a “dummy” write operation.
The master issues the start condition and the slave
address byte, receives an acknowledge, then issues
the word address bytes. After acknowledging receipt
of each word address byte, the master immediately
issues another start condition and the slave address
byte with the R/W bit set to one. This is followed by an
acknowledge from the device and then by the eight bit
data word. The master terminates the read operation
by not responding with an acknowledge and then issu-
ing a stop condition. Refer to Figure 17 for the
address, acknowledge, and data transfer sequence.
In a similar operation called “Set Current Address,” the
device sets the address if a stop is issued instead of
the second start shown in Figure 17. The X1288 then
goes into standby mode after the stop and all bus
activity will be ignored until a start is detected. This
operation loads the new address into the address
counter. The next Current Address Read operation will
read from the newly loaded address. This operation
could be useful if the master knows the next address it
needs to read, but is not ready for the data.
Sequential Read
Sequential reads can be initiated as either a current
address read or random address read. The first data
byte is transmitted as with the other modes; however,
the master now responds with an acknowledge, indi-
cating it requires additional data. The device continues
to output data for each acknowledge received. The
master terminates the read operation by not responding
with an acknowledge and then issuing a stop condition.
The data output is sequential, with the data from
address n followed by the data from address n + 1.
The address counter for read operations increments
through all page and column addresses, allowing the
entire memory contents to be serially read during one
operation. At the end of the address space the counter
“rolls over” to the start of the address space and the
X1288 continues to output data for each acknowledge
received. Refer to Figure 18 for the acknowledge and
data transfer sequence.
ACK
returned?
Issue Slave
Address Byte
(Read or Write)
Byte load completed
by issuing STOP.
Enter ACK Polling
Issue STOP
Issue START
NO
YES
Issue STOP
NO
Continue normal
Read or Write
command
sequence
PROCEED
YES
nonvolatile write
Cycle complete. Continue
command sequence?
FIGURE 16. ACKNOWLEDGE POLLING SEQUENCE
X1288
相關PDF資料 |
PDF描述 |
|---|---|
| X1288V14Z-2.7 | IC RTC/CAL/CPU SUP EE 14-TSSOP |
| X1288V14Z | IC RTC/CAL/CPU SUP EE 14-TSSOP |
| MCP4241T-103E/ML | IC DGTL POT 10K 2CH 16QFN |
| X1288V14Z-2.7A | IC RTC/CAL/CPU SUPERVSR 14-TSSOP |
| MCP4241T-103E/SL | IC DGTL POT 10K 2CH 14SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X1288V14ZT1 | 功能描述:IC RTC/CAL/CPU SUP EE 14-TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
| X-1293 | 制造商:Pulse 功能描述:TRANSFORMERS - Rail/Tube |
| X-1297-1 | 制造商:Pulse Electronics Corporation 功能描述:DATA BUS - Rail/Tube |
| X-1298-1 | 制造商:Pulse Electronics Corporation 功能描述:TRANSFORMERS - Rail/Tube |
| X12CP | 制造商:APEM 功能描述:SPST standard toggle switch,15A |
發布緊急采購，3分鐘左右您將得到回復。