- 您現在的位置：買賣IC網 > PDF目錄372527 > X1227V8Z-4.5A (INTERSIL CORP) 16 Characters x 1 Lines, 5x7 Dot Matrix Character and Cursor PDF資料下載
參數資料
| 型號： | X1227V8Z-4.5A |
| 廠商： | INTERSIL CORP |
| 元件分類： | XO, clock |
| 英文描述： | 16 Characters x 1 Lines, 5x7 Dot Matrix Character and Cursor |
| 中文描述： | 1 TIMER(S), REAL TIME CLOCK, PDSO8 |
| 封裝： | ROHS COMPLIANT, PLASTIC, MO-153AC, TSSOP-8 |
| 文件頁數： | 22/28頁 |
| 文件大?。?/td> | 442K |
| 代理商： | X1227V8Z-4.5A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁
X1227
REV 1.1.20 1/13/03
Characteristics subject to change without notice.
22 of 28
www.xicor.com
A final application for the ATR control is in-circuit cali-
bration for high accuracy applications, along with a
temperature sensor chip. Once the RTC circuit is pow-
ered up with battery backup, the frequency drift is mea-
sured. The ATR control is then adjusted to a setting
which minimizes drift. Once adjusted at a particular
temperature, it is possible to adjust at other discrete
temperatures for minimal overall drift, and store the
resulting settings in the EEPROM. Extremely low over-
all temperature drift is possible with this method. The
Xicor evaluation board contains the circuitry necessary
to implement this control.
For more detailed operation see Xicor’s application
note AN154 on Xicor’s website at www.xicor.com.
Layout Considerations
The crystal input at X1 has a very high impedance and
will pick up high frequency signals from other circuits
on the board. Since the X2 pin is tied to the other side
of the crystal, it is also a sensitive node. These signals
can couple into the oscillator circuit and produce dou-
ble clocking or mis-clocking, seriously affecting the
accuracy of the RTC. Care needs to be taken in layout
of the RTC circuit to avoid noise pickup. Below in Fig-
ure 15 is a suggested layout for the X1226 or X1227
devices.
Figure 15. Suggested Layout for Xicor RTC in SO-8
The X1 and X2 connections to the crystal are to be
kept as short as possible. A thick ground trace around
the crystal is advised to minimize noise intrusion, but
ground near the X1 and X2 pins should be avoided as
it will add to the load capacitance at those pins. Keep in
mind these guidelines for other PCB layers in the vicin-
ity of the RTC device. A small decoupling capacitor at
the Vcc pin of the chip is mandatory, with a solid con-
nection to ground.
For other RTC products, the same rules stated above
should be observed, but adjusted slightly since the
packages and pinouts are slightly different.
Assembly
Most electronic circuits do not have to deal with
assembly issues, but with the RTC devices assembly
includes insertion or soldering of a live battery into an
unpowered circuit. If a socket is soldered to the board,
and a battery is inserted in final assembly, then there
are no issues with operation of the RTC. If the battery
is soldered to the board directly, then the RTC device
Vback pin will see some transient upset from either sol-
dering tools or intermittent battery connections which
can stop the circuit from oscillating. Once the battery is
soldered to the board, the only way to assure the circuit
will start up is to momentarily (very short period of
time!) short the Vback pin to ground and the circuit will
begin to oscillate.
Oscillator Measurements
When a proper crystal is selected and the layout guide-
lines above are observed, the oscillator should start up
in most circuits in less than one second. Some circuits
may take slightly longer, but startup should definitely
occur in less than 5 seconds. When testing RTC cir-
cuits, the most common impulse is to apply a scope
probe to the circuit at the X2 pin (oscillator output) and
observe the waveform. DO NOT DO THIS! Although in
some cases you may see a useable waveform, due to
the parasitics (usually 10pF to ground) applied with the
scope probe, there will be no useful information in that
waveform other than the fact that the circuit is oscillat-
ing. The X2 output is sensitive to capacitive impedance
so the voltage levels and the frequency will be affected
相關PDF資料 |
PDF描述 |
|---|---|
| X1227V8IZ-4.5A | 16 Characters x 1 Lines, 5x7 Dot Matrix Character and Cursor |
| X1227V8I-2.7 | RTC Module With CPU Supervisor |
| X1227S8Z-2.7A | RTC Module With CPU Supervisor |
| X1227S8IZ-2.7 | RTC Module With CPU Supervisor |
| X1227V8IZ-2.7 | RTC Module With CPU Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X1228 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Real Time Clock/Calendar/CPU Supervisor with EEPROM |
| X1228_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Real Time Clock/Calendar/CPU Supervisor with EEPROM |
| X1228EVM | 制造商:Intersil Corporation 功能描述:A Evaluation Board (Connecting to X1228 Through PIC16C57 MCU,and Testing All Functions,Including Settings of Time,Alarm,Programmable Frequency Output,Digital/Analog Tuning,Watchdog and Reset Threshold),and A Development Data CD 制造商:Intersil Corporation 功能描述:A Evaluation Board (Connecting to X1228 Through PIC16C57 MCU, and Testing All Functions, Including Settings of Time, Alarm, Programmable Frequency Output, Digital/Analog Tuning, Watchdog and Reset Threshold), and A Development Data CD |
| X1228S14 | 功能描述:IC RTC CPU SUP WDT 4K EE 14-SOIC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
| X1228S14-2.7 | 功能描述:IC RTC CPU SUP WDT 4K EE 14-SOIC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。