- 您現在的位置：買賣IC網 > PDF目錄372527 > X1226S8 (INTERSIL CORP) Real Time Clock/Calendar with EEPROM PDF資料下載
參數資料
| 型號： | X1226S8 |
| 廠商： | INTERSIL CORP |
| 元件分類： | XO, clock |
| 英文描述： | Real Time Clock/Calendar with EEPROM |
| 中文描述： | 1 TIMER(S), REAL TIME CLOCK, PDSO8 |
| 封裝： | 0.150 INCH, SOIC-8 |
| 文件頁數： | 9/24頁 |
| 文件大小： | 420K |
| 代理商： | X1226S8 |
X1226
REV 1.1.24 1/13/03
Characteristics subject to change without notice.
9 of 24
www.xicor.com
Figure 4. Valid Start and Stop Conditions
SCL
SDA
Start
Stop
Figure 5. Acknowledge Response From Receiver
SCL from
Master
Data Output
from Transmitter
Data Output
from Receiver
8
1
9
Start
Acknowledge
DEVICE ADDRESSING
Following a start condition, the master must output a
Slave Address Byte. The first four bits of the Slave
Address Byte specify access to either the EEPROM
array or to the CCR. Slave bits ‘1010’ access the
EEPROM array. Slave bits ‘1101’ access the CCR.
When shipped from the factory, EEPROM array is
UNDEFINED, and should be programmed by the cus-
tomer to a known state.
Bit 3 through Bit 1 of the slave byte specify the device
select bits. These are set to ‘111’.
The last bit of the Slave Address Byte defines the oper-
ation to be performed. When this R/W bit is a one, then
a read operation is selected. A zero selects a write
operation. Refer to Figure 6.
After loading the entire Slave Address Byte from the
SDA bus, the X1226 compares the device identifier
and device select bits with ‘1010111’ or ‘1101111’.
Upon a correct compare, the device outputs an
acknowledge on the SDA line.
Following the Slave Byte is a two byte word address.
The word address is either supplied by the master
device or obtained from an internal counter. On power
up the internal address counter is set to address 0h, so
a current address read of the EEPROM array starts at
address 0. When required, as part of a random read,
the master must supply the 2 Word Address Bytes as
shown in Figure 6.
In a random read operation, the slave byte in the
“dummy write” portion must match the slave byte in the
“read” section. That is if the random read is from the
array the slave byte must be 1010111x in both
instances. Similarly, for a random read of the Clock/
Control Registers, the slave byte must be 1101111x in
both places.
相關PDF資料 |
PDF描述 |
|---|---|
| X1226S8I | POT 500 OHM 6MM CERMET VERT |
| X1226S8IT1 | POT 500 OHM 6MM CERMET VERT |
| X1226S8IZ | POT 5.0K OHM 6MM CERMET VERT |
| X1226V8IT1 | Real Time Clock/Calendar with EEPROM |
| X1226S8IZT1 | Real Time Clock/Calendar with EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X1226S8I | 功能描述:IC RTC/CALENDAR/4K EE 8-SOIC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
| X1226S8IT1 | 功能描述:IC RTC/CALENDAR/4K EE 8-SOIC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
| X1226S8IZ | 功能描述:IC RTC/CALENDAR/ALARM 4K 8-SOIC RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
| X1226S8IZT1 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Real Time Clock/Calendar with EEPROM |
| X1226S8T1 | 功能描述:IC RTC/CALENDAR/4K EE 8-SOIC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。