- 您現在的位置：買賣IC網 > PDF目錄361881 > WM9703 (Wolfson Microelectronics) TVS UNIDIRECT 400W 22V SMA PDF資料下載
參數資料
| 型號： | WM9703 |
| 廠商： | Wolfson Microelectronics |
| 英文描述： | TVS UNIDIRECT 400W 22V SMA |
| 中文描述： | AC97音頻編解碼器2.1版 |
| 文件頁數： | 25/30頁 |
| 文件大?。?/td> | 239K |
| 代理商： | WM9703 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁
Production Data
WM9703
WOLFSON MICROELECTRONICS LTD
PD Rev 3.4 January 2001
25
Figure 17 illustrates one example of a procedure to do a complete powerdown of the WM9703. From
normal operation sequential writes to the Powerdown Register are performed to powerdown the
WM9703 a piece at a time. After everything has been shut off (PR0 to PR3 set), a final write (of PR4)
can be executed to shut down the WM9703
’
s digital interface (AC-link).
The part will remain in sleep mode with all its registers holding their static values. To wake up the
WM9703, the AC
’
97 controller will send a pulse on the sync line issuing a warm reset. This will
restart the WM9703
’
s digital interface (resetting PR4 to 0). The WM9703 can also be woken up with
a cold reset. A cold reset will cause a loss of values of the registers, as a cold reset will set them to
their default states. When a section is powered back on, the Powerdown Control/Status Register
index 26h should be read to verify that the section is ready (i.e. stable) before attempting any
operation that requires it.
Alternatively if RESETB is held low, all PR bits are held set so the device is held powered off until
RESETB is taken high again.
PR1 = 1
PR2 = 1
PR4 = 1
ADCs OFF
PR0
DACs OFF
PR1
ANALOGUE
OFF PR2
OR PR3
DIGITAL I/F
OFF PR4
WARM RESET
PR1 = 0 AND
DAC = 1
PR2 = 0 AND
ANL = 1
SHUT OFF
CODA LINK
Figure 18 The WM9703 Powerdown/Flow with Analogue Still Alive
Figure 18 illustrates a state when all the mixers should work with the static volume settings that are
contained in their associated registers. This is used when the user is playing a CD (or external
LINEIN source) through WM9703 to the speakers but has most of the system in low power mode.
The procedure for this follows the previous except that the analogue mixer is never shut down.
POWERDOWN CONTROL/STATUS REGISTER (INDEX 26h)
Note that in order to go into ultimate low power mode, PR5 is required to be set which turns off the
oscillator circuit. Asserting SYNC resets the PR5 bit and re-starts the oscillator in the same was as
the AC link is restarted.
Also when RESETB pin is asserted low, all PR bits are over-ridden and the entire device is powered
off to ultra low power state for as long as RESETB = low. On releasing RESETB, the device is reset
(all active) and powered up.
REVISION 2.1 REGISTERS (INDEX 28h T0 58h)
These registers are specified as to use in Revision 2.1 of the AC
’
97 specification and have the
following functions on the WM9703:
REGISTER 28h
–
EXTENDED AUDIO ID
The Extended Audio ID register is a read only register that identifies which extended audio features
are supported (in addition to the original AC
’
97 features identified by reading the reset register at
index 00h). A non zero value indicates the feature is supported.
相關PDF資料 |
PDF描述 |
|---|---|
| WM9712L | AC97 Audio and Touchpanel CODEC |
| WM9712LEFL | AC97 Audio and Touchpanel CODEC |
| WM9712LEFT | AC97 Audio and Touchpanel CODEC |
| WM9712LEFV | AC97 Audio and Touchpanel CODEC |
| WM9712LSEFL | AC97 Audio and Touchpanel CODEC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| WM9703CFT/V | 制造商:WOLFSON 制造商全稱:WOLFSON 功能描述:AC97 Revision 2.1 Audio Codec |
| WM9704CFT/V | 制造商:WOLFSON 制造商全稱:WOLFSON 功能描述:4-Channel Surround Sound Codec |
| WM9704M | 制造商:WOLFSON 制造商全稱:WOLFSON 功能描述:AMC97 Audio and Modem Codec |
| WM9704Q | 制造商:WOLFSON 制造商全稱:WOLFSON 功能描述:4-Channel Surround Sound Codec |
| WM9705 | 制造商:WOLFSON 制造商全稱:WOLFSON 功能描述:Multimedia AC97 CODEC with Integrated Touch Screen Controller |
發布緊急采購，3分鐘左右您將得到回復。