- 您現在的位置：買賣IC網 > PDF目錄363899 > W78L058A24PL (WINBOND ELECTRONICS CORP) 8-BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | W78L058A24PL |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT MICROCONTROLLER |
| 中文描述： | 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQCC44 |
| 封裝： | ROHS COMPLIANT, PLASTIC, LCC-44 |
| 文件頁數： | 8/34頁 |
| 文件大?。?/td> | 238K |
| 代理商： | W78L058A24PL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
W78LE58/W78L058A
- 8 -
Mode 3: P4.0
P4.3 are read/write strobe signals that are synchronized with
RD
or
WR
signal at
specified addresses. These signals can be used as chip-select signals for external
peripherals.
When Port 4 is configured with the feature of chip-select signals, the chip-select signal address range
depends on the contents of the SFR P4xAH, P4xAL, P4CONA and P4CONB. The registers P4xAH
and P4xAL contain the 16-bit base address of P4.x. The registers P4CONA and P4CONB contain the
control bits to configure the Port 4 operation mode.
INT2
/
INT3
Two additional external interrupts,
INT2
and
INT3
, whose functions are similar to those of external
interrupt 0 and 1 in the standard 80C52. The functions/status of these interrupts are
determined/shown by the bits in the XICON (External Interrupt Control) register. The XICON register is
bit-addressable but is not a standard register in the standard 80C52. Its address is at 0C0H. To
set/clear bits in the XICON register, one can use the "SETB (
CLR
) bit" instruction. For example,
"SETB 0C2H" sets the EX2 bit of XICON.
XICON - external interrupt control (C0H)
PX3
PX3: External interrupt 3 priority high if set
EX3: External interrupt 3 enable if set
IE3: If IT3 = 1, IE3 is set/cleared automatically by hardware when interrupt is detected/serviced
IT3: External interrupt 3 is falling-edge/low-level triggered when this bit is set/cleared by software
PX2: External interrupt 2 priority high if set
EX2: External interrupt 2 enable if set
IE2: If IT2 = 1, IE2 is set/cleared automatically by hardware when interrupt is detected/serviced
IT2: External interrupt 2 is falling-edge/low-level triggered when this bit is set/cleared by software
Eight-source interrupt information:
EX3
IE3
IT3
PX2
EX2
IE2
IT2
INTERRUPT
SOURCE
VECTOR
ADDRESS
POLLING
SEQUENCE WITHIN
PRIORITY LEVEL
0 (highest)
1
2
3
4
5
6
7 (lowest)
ENABLE
REQUIRED
SETTINGS
IE.0
IE.1
IE.2
IE.3
IE.4
IE.5
XICON.2
XICON.6
INTERRUPT TYPE
EDGE/LEVEL
External Interrupt 0
Timer/Counter 0
External Interrupt 1
Timer/Counter 1
Serial Port
Timer/Counter 2
External Interrupt 2
External Interrupt 3
03H
0BH
13H
1BH
23H
2BH
33H
3BH
TCON.0
-
TCON.2
-
-
-
XICON.0
XICON.3
相關PDF資料 |
PDF描述 |
|---|---|
| W78L32 | 8-BIT Microcontroller(8位的微控制器) |
| W78L32F-24 | 8-BIT MICROCONTROLLER |
| W78L32P-24 | 8-BIT MICROCONTROLLER |
| W78L32-24 | 8-BIT MICROCONTROLLER |
| W78L33 | 8-BIT Microcontroller(8位的微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W78L32 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W78L32_06 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W78L32-24 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W78L32F-24 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W78L32P-24 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。