- 您現在的位置：買賣IC網 > PDF目錄245661 > W332M72V-133SBI (MICROSEMI CORP-PMG MICROELECTRONICS) 32M X 72 SYNCHRONOUS DRAM, 5.5 ns, PBGA208 PDF資料下載
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁
7
White Electronic Designs
W332M72V-XBX
March 2006
Rev. 3
White Electronic Designs Corporation (602) 437-1520 www.wedc.com
TRUTH TABLE - COMMANDS AND DQM OPERATION (NOTE 1)
NAME (FUNCTION)
CS#
RAS#
CAS#
WE#
DQM
ADDR
I/Os
COMMAND INHIBIT (NOP)
H
X
NO OPERATION (NOP)
L
H
X
ACTIVE (Select bank and activate row) ( 3)
L
H
X
Bank/Row
X
READ (Select bank and column, and start READ burst) (4)
L
H
L
H
L/H 8
Bank/Col
X
WRITE (Select bank and column, and start WRITE burst) (4)
L
H
L
L/H 8
Bank/Col
Valid
BURST TERMINATE
L
H
L
X
Active
PRECHARGE (Deactivate row in bank or banks) ( 5)
L
H
L
X
Code
X
AUTO REFRESH or SELF REFRESH (Enter self refresh mode) (6, 7)
L
H
X
LOAD MODE REGISTER (2)
L
X
Op-Code
X
Write Enable/Output Enable (8)
––––
L
–
Active
Write Inhibit/Output High-Z (8)
––––
H
–
High-Z
Register Denition section. The LOAD MODE REGISTER
command can only be issued when all banks are idle, and
a subsequent executable command cannot be issued until
tMRD is met.
ACTIVE
The ACTIVE command is used to open (or activate) a
row in a particular bank for a subsequent access. The
value on the BA0, BA1 inputs selects the bank, and the
address provided on inputs A0-12 selects the row. This row
remains active (or open) for accesses until a PRECHARGE
command is issued to that bank. A PRECHARGE
command must be issued before opening a different row
in the same bank.
READ
The READ command is used to initiate a burst read
access to an active row. The value on the BA0, BA1 inputs
selects the bank, and the address provided on inputs A0-9
selects the starting column location. The value on input
A10 determines whether or not AUTO PRECHARGE is
used. If AUTO PRECHARGE is selected, the row being
accessed will be precharged at the end of the READ
burst; if AUTO PRECHARGE is not selected, the row will
remain open for subsequent accesses. Read data appears
COMMANDS
The Truth Table provides a quick reference of available
commands. This is followed by a written description of each
command. Three additional Truth Tables appear following
the Operation section; these tables provide current state/
next state information.
COMMAND INHIBIT
The COMMAND INHIBIT function prevents new commands
from being executed by the SDRAM, regardless of whether
the CLK signal is enabled. The SDRAM is effectively
deselected. Operations already in progress are not
affected.
NO OPERATION (NOP)
The NO OPERATION (NOP) command is used to perform
a NOP to an SDRAM which is selected (CS# is LOW).
This prevents unwanted commands from being registered
during idle or wait states. Operations already in progress
are not affected.
LOAD MODE REGISTER
The Mode Register is loaded via inputs A0-11 (A12
should be driven low). See Mode Register heading in the
NOTES:
1. CKE is HIGH for all commands shown except SELF REFRESH.
2. A0-11 dene the op-code written to the Mode Register and A12 should be driven
low.
3. A0-12 provide row address, and BA0, BA1 determine which bank is made active.
4. A0-9 provide column address; A10 HIGH enables the auto precharge feature
(nonpersistent), while A10 LOW disables the auto precharge feature; BA0, BA1
determine which bank is being read from or written to.
5. A10 LOW: BA0, BA1 determine the bank being precharged. A10 HIGH: All banks
precharged and BA0, BA1 are “Don’t Care.”
6. This command is AUTO REFRESH if CKE is HIGH; SELF REFRESH if CKE is
LOW.
7. Internal refresh counter controls row addressing; all inputs and I/Os are “Don’t Care”
except for CKE.
8. Activates or deactivates the I/Os during WRITEs (zero-clock delay) and READs
(two-clock delay).
相關PDF資料 |
PDF描述 |
|---|---|
| WED3EG7233S265D3G | SYNCHRONOUS DRAM MODULE, DMA184 |
| W7NCF02GH11IS8CG | 128M X 16 FLASH 3.3V PROM CARD, 150 ns, UUC |
| W7NCF02GH11IS5AG | 128M X 16 FLASH 3.3V PROM CARD, 150 ns, UUC |
| W7NCF02GH11IS3DG | 128M X 16 FLASH 3.3V PROM CARD, 150 ns, UUC |
| W25X80ALDAIZ | 1M X 8 FLASH 2.7V PROM, PDIP8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W332M72V-133SBM | 制造商:Microsemi Corporation 功能描述:32M X 72 SDRAM, 3.3V, 133MHZ, 208 PBGA, MIL-TEMP. - Bulk |
| W332M72V-XBX | 制造商:WEDC 制造商全稱:White Electronic Designs Corporation 功能描述:32Mx72 Synchronous DRAM |
| W332M72V-XSBX | 制造商:WEDC 制造商全稱:White Electronic Designs Corporation 功能描述:32Mx72 Synchronous DRAM |
| W3330X6 | 制造商:n/a 功能描述:Ships in 2 days |
| W3331 | 功能描述:RF ANT TRACE 895MHZ 2.4GHZ SMD 制造商:pulselarsen antennas 系列:- 包裝:散裝 零件狀態:在售 頻率組:UHF（300 MHz ~ 1 GHz），UHF（2 GHz ~ 3 GHz） 頻率（中心/帶）:895MHz，2.4GHz 頻率范圍:863MHz ~ 928MHz，2.4GHz ~ 2.5GHz 天線類型:PCB 印制線 頻帶數:2 VSWR:- 回波損耗:-15dB 增益:3.5dBi 功率 - 最大值:3W 特性:- 端接:焊接 侵入防護:- 安裝類型:表面貼裝 高度（最大值）:0.031"（0.80mm） 應用:藍牙，WLAN，Zigbee? 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。