Coil
measured @ 25 C
W9AS1D22-5
W9ASID22-12
W9ASID22-24
W9ASID22-48
W9ASID22-110
SPST-NO
30AMP
P.C. MT.
FIGURE "A"
W9AS5D22-5
W9AS5D22-12
W9AS5D22-24
W9AS5D22-48
W9AS5D22-110
SPDT
30AMP
P.C. MT.
FIGURE "A"
W9AS1D52-5
W9ASID52-12
W9ASID52-24
W9ASID52-48
W9ASID52-110
SPST-NO
30AMP-
FLANGE MT.
FIGURE "B"
W9AS5D52-5
W9AS5D52-12
W9AS5D52-24
W9AS5D52-48
W9AS5D52-110
SPDT
30AMP
FLANGE MT.
FIGURE "B"
5
12
24
48
110
25
144
576
2,304
12,100
DC OPERATED COIL
1W
1W
1W
1W
1W
NOMINAL
RESIS-
TANCE
(Ohms)
NOMINAL
POWER
(Watts)
NOMINAL
INPUT
VOLTAGE
PART NUMBERS SHOWN ALSO
AVAILABLE THRU STOCKING DISTRIBUTION.
PART NUMBERS
SPECIFICATIONS CLASS 9A
-55C to +85C
-55C to +130C
10 to 55Hz 1.65 mm
max. No contact opening > 00 uS
10 g's for 11 mS, No contact Opening
> 100
μ
S
100 g's
100,000 Operations
10 million Operations Typical
Any
Epoxy sealed immersion cleanable
suitable for automatic circuit board
processing. Max. exposure soldering
temperature is 4 sec. @ 500F.
94V-O Flammability rating.
1/4" Q.C. & safety wells accept insulated
Female Q.C. terminals.
33 Grams, 1.2 oz approx.
TEMPERATURE
Operating:
Storage:
VIBRATION RESISTANCE
Functional:
SHOCK RESISTANCE
Functional:
Mechanical:
LIFE
Electrical (Rated Load)
Mechanical (No Load):
MISCELLANEOUS
Operating Position:
Enclosure:
Enclosure:
Terminals:
Weight:
COIL
Pull-in Voltage:
Dropout voltage:
Max. coil voltage:
Power consumption:
Duty:
Insulation System:
Coil Resistance
CONTACT
Contact Configuration:
Contact Material:
Switching voltage:
Contact Resistance:
Minimum Load:
TIMING
Operate Time:
Release Time:
DIELECTRIC STRENGTH
Between Open Contacts:
Contacts to coil:
Insulation Resistance
75% of Nominal Voltage or Less
10% of Nominal voltage or More
120% Max.
2.8 Watts max.
Continuous
Class "F" (155C)
±
10% Measured @ 25C
SPST-N.O., SPDT
Silver Cadmium Oxide
277 VAC, 28VDC max.
75 Milliohms @ 1 min, rated current
(switched)
1A, 5VDC, 12VAC
DC:15 mS typ. including bounce
DC:15mS typ. including bounce
1500 V rms
2500V rms
1000 m
min. @ 500 VDC, 25C 50% RH
30 AMP PC or FLANGE MOUNT MINIATURE RELAY
C L A S S
9A
PAGE 50
WEBSITE: www.magnecraft.com - EMAIL:info@magnecraft.com - FAX ON DEMAND 1-800/891-2957 - DOCUMENT 100
GENERAL PURPOSE
RESISTIVE
RESISTIVE HEATER
MOTOR (HP)
MOTOR
FLA/LRA
TUNGSTEN
BALLAST
PILOT DUTY
LOAD
VOLTAGE
N.O.
RATING
N.C.
N.O.
SPDT
N.C.
100,000
100,000
100,000
100,000
1,000
1,000
30,000
30,000
25,000
6,000
6,000
AC Measured @ 50/60Hz
10A
15A
10A
-
1/4 HP
1/2 HP
-
12/30A
-
3A
275 VA
20A
20A
20A
-
1 HP
2 HP
-
30/80A
TV-5
10A
470 VA
*15A
15A
10A
-
1/4 HP
1/2 HP
-
12/30A
-
3A
275 VA
30A
20A
20A
25A
1 HP
2 HP
22/98A
30/80A
TV-5
10A
470 VA
240 VAC
240 VAC
28 VDC
240 VAC
125 VAC
240 VAC
120 VAC
240 VAC
240 VAC
277 VAC
240 VAC
OPERATIONS
Meets UL 508, UL 873 and UL 1950 - 1/8" thru air - 1/4" over surface (See Foot notes)
* 15 Amp general purpose rating on SPST-NC contact valid only under UL 508 column B spacings and UL
873 columns B, C & D spacings. Derate to 10 Amps when used under UL 873 columns E & F spacings
and UL 1950.
15 Amp resistive rating on SPST-NC contacts and SPDT contacts (Normally closed side only) valid only
under UL 873 columns E & F spacings. Derate to 10 Amps when used under UL 508 Column B spacings,
under UL 873 columns B, C & D spacings and UL 1950.
The resistance heater rating is not a discreet UL heater rating but is a valid UL rating that is derived
from the UL general purpose category in the above table of contact ratings.
FLA = Full load Amps, LRA = Locked rotor Amps.
CONTACT RATINGS
SPST