- 您現在的位置：買賣IC網 > PDF目錄359430 > VSC7940RP (VITESSE SEMICONDUCTOR CORP) SONET/SDH 3.125Gb/s Laser Diode Driver with Automatic Power Control PDF資料下載
參數資料
| 型號： | VSC7940RP |
| 廠商： | VITESSE SEMICONDUCTOR CORP |
| 元件分類： | 其它接口 |
| 英文描述： | SONET/SDH 3.125Gb/s Laser Diode Driver with Automatic Power Control |
| 中文描述： | SPECIALTY INTERFACE CIRCUIT, PQFP32 |
| 封裝： | 5 X 5 MM, TQFP-32 |
| 文件頁數： | 9/16頁 |
| 文件大小： | 167K |
| 代理商： | VSC7940RP |
VITESSE
Preliminary Data Sheet
VSC7940
SONET/SDH 3.125Gb/s
Laser Diode Driver with Automatic Power Control
G52357-0, Rev 3.2
05/11/01
Page 9
VITESSE
SEMICONDUCTOR CORPORATION
741 Calle Plano
Camarillo, CA 93012
Tel: (800) VITESSE
FAX: (805) 987-5896
Email: prodinfo@vitesse.com
Internet: www.vitesse.com
Enable/Disable
Two pins are provided to allow either ENABLE or DISABLE control. If ENABLE is used, connect DIS-
ABLE to ground. Is DISABLE is used, leave ENABLE floating. Both modulation and bias currents are turned
off when ENABLE is low or DISABLE is high. Typically, ENABLE or DISABLE responds to within approxi-
mately 250ns.
Controlling the Modulation Current
The output modulation current may be determined from the following equation where P
p-p
is the peak-to-
peak optical power, P
AVE
is the average power, r
e
is the extinction ratio, and
η
is the laser slope efficiency:
I
MOD
= P
p-p
/
η
= 2 * P
AVE
* (r
e
-1) / (r
e
+1) /
η
A resistor at MODSET controls the output bias current. Graphs of I
MODSET
vs. R
MODSET
in
Typical Operat-
ing Characteristics
describe the relationship between the resistor at MODSET and the output modulation cur-
rent at 25
°
C. After determining the desired output modulation current, use the graph to determine the
appropriate resistor value at MODSET.
Controlling the Bias Current
A resistor at BIASMAX should be used to control the output bias current. Graphs of I
BIASMAX
vs. R
BIASMAX
in
Typical Operating Characteristics
describe the relationship between the resistor at BIASMAX and the output
bias current at 25
°
C. If the APC is not used, the appropriate resistor value at BIASMAX is determined by first
selecting the desired output bias current, and then using the graph to determine the appropriate resistor value at
BIASMAX. When using APC, BIASMAX sets the maximum allowed bias current. After determining the max-
imum end-of-life bias current at 85
°
C for the laser, refer to the graph of I
BIASMAX
vs. R
BIASMAX
in
Typical Oper-
ating Characteristics
to select the appropriate resistor value.
Controlling the APC Loop
To select the resistor at APCSET, use the graph of I
MD
vs. R
APCSET
in
Typical Operating Characteristics.
The graph relates the desired monitor current to the appropriate resistance value at APCSET. I
MD
may be calcu-
late from the desired optical average power, P
AVE,
, and the laser-to-monitor transfer,
ρ
MON
, for a specific laser
using the following equation:
I
MD
= P
AVE
*
ρ
MON
Laser Diode Interface
An RC shunt network should be placed at the laser output interface. The sum of the resistor placed at the
output and the laser diode resistance should be 25
. For example, if the laser diode has a resistance of 5
, a
20
resistor should be placed in series with the laser. For optimal performance, a bypass capacitor should be
placed close to the laser anode.
A
“
snubber network
”
consisting of a capacitor C
F
and resistor R
F
should be placed at the laser output to
minimize reflections from the laser (see Block Diagram). Suggested values for these components are 80
and
2pF, respectively, however, these values should be adjusted until an optical output waveform is obtained.
相關PDF資料 |
PDF描述 |
|---|---|
| VSC7940 | SONET/SDH 3.125Gb/s Laser Diode Driver with Automatic Power Control |
| VSC7940W | SONET/SDH 3.125Gb/s Laser Diode Driver with Automatic Power Control |
| VSC7958 | 2.5Gb/s High Speed Limiting Post Amplifier for OC-48/SDH-16 Applications |
| VSC7958CC | 2.5Gb/s High Speed Limiting Post Amplifier for OC-48/SDH-16 Applications |
| VSC7958X | 2.5Gb/s High Speed Limiting Post Amplifier for OC-48/SDH-16 Applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| VSC7940W | 制造商:VITESSE 制造商全稱:Vitesse Semiconductor Corporation 功能描述:SONET/SDH 3.125Gb/s Laser Diode Driver with Automatic Power Control |
| VSC7958 | 制造商:VITESSE 制造商全稱:Vitesse Semiconductor Corporation 功能描述:2.5Gb/s High Speed Limiting Post Amplifier for OC-48/SDH-16 Applications |
| VSC7958CC | 制造商:VITESSE 制造商全稱:Vitesse Semiconductor Corporation 功能描述:2.5Gb/s High Speed Limiting Post Amplifier for OC-48/SDH-16 Applications |
| VSC7958X | 制造商:VITESSE 制造商全稱:Vitesse Semiconductor Corporation 功能描述:2.5Gb/s High Speed Limiting Post Amplifier for OC-48/SDH-16 Applications |
| VSC7959 | 制造商:VITESSE 制造商全稱:Vitesse Semiconductor Corporation 功能描述:3.125Gb/s CML Limiting Amplifier with LOS Detect |
發布緊急采購，3分鐘左右您將得到回復。