- 您現在的位置：買賣IC網 > PDF目錄359430 > VSC7938R0 (Vitesse Semiconductor Corporation.) Laser Diode Driver with Automatic Power Control PDF資料下載
參數資料
| 型號： | VSC7938R0 |
| 廠商： | Vitesse Semiconductor Corporation. |
| 英文描述： | Laser Diode Driver with Automatic Power Control |
| 中文描述： | 激光二極管驅動器，帶有自動功率控制 |
| 文件頁數： | 8/16頁 |
| 文件大?。?/td> | 213K |
| 代理商： | VSC7938R0 |
VITESSE
Preliminary Data Sheet
VSC7938
SONET/SDH 3.125Gb/s
Laser Diode Driver with Automatic Power Control
Page 8
G52349-0, Rev 3.0
01/20/01
VITESSE
SEMICONDUCTOR CORPORATION
741 Calle Plano
Camarillo, CA 93012
Tel: (800) VITESSE
FAX: (805) 987-5896
Email: prodinfo@vitesse.com
Internet: www.vitesse.com
Detailed Description
The VSC7938 is a high-speed laser driver with Automatic Power Control. The device is designed to operate
up to 3.125Gb/s with a 3.3V or 5V supply. The data and clock inputs support PECL inputs as well as other
inputs that meet the common-mode voltage and differential voltage swing specifications. The differential pair
output stage is capable of sinking up to 60mA from the laser with typical rise and fall times of 60ps. This output
may be DC-coupled for 5V operation. To allow for larger output swings during 3.3V operation, the VSC7938
was designed to be AC-coupled to the laser cathode with a pull-up inductor for DC-biasing. This configuration
will isolate laser forward voltage from the output circuitry and will allow the output at OUT+ to swing above
and below the supply voltage V
CC
. The key features of the VSC7938 are Automatic Power Control, low power
supply current, and fast rise and fall times. The VSC7939 and VSC7940 are other Vitesse laser drivers with
similar features in a 32-pin TQFP package. These devices also have pins for monitoring modulation and bias
currents. The VSC7940 is a special version of the VSC7939 designed to drive 100mA into a DC-coupled load
with a 5V supply.
Automatic Power Control
To ensure constant average optical power, the device utilizes an Automatic Power Control loop. A photo-
diode mounted in the laser package provides optical feedback to compensate for changes in average laser output
power due to changes that affect laser performance such as temperature and laser lifetime. The laser bias current
is adjusted by the APC loop according to the reference current set at APCSET by an external resistor. An exter-
nal capacitor at CAPC controls the time constant for the APC feedback loop. The recommended value for
CAPC is 0.1
μ
F. This value reduces pattern-dependent jitter associated with the APC feedback loop and guaran-
tees stability. Because the APC loop noise is internally filtered, APCFILT is not internally connected and does
not need to be connected to any external components. The device
’
s performance will not be affected if a capac-
itor is connected to APCFILT. If the APC loop cannot adjust the bias current to track the desired monitor cur-
rent, FAIL is set low.
The device may be operated with or without APC. To utilize APC, a capacitor must be connected at CAPC
(0.1
μ
F) and a resistor must be connected at APCSET to set the average optical power. For open-loop operation
(no APC), a 100k
resistor should be connected between APCSET and GND. CAPC has no effect on open-
loop operation. In both modes of operation, resistors to ground should be placed at BIASMAX and MODSET to
set the bias and modulation currents.
Data Retiming
The VSC7938 provides inputs for differential PECL clock signals for data retiming to minimize jitter at
high speeds. To incorporate this function, LATCH should be connected to V
CC
. If this function is unused,
CLK+ should be connected to V
CC
, CLK- should be left unconnected, and LATCH should be connected to
GND.
Short-Circuit Protection
If BIASMAX or MODSET are shorted to ground, the output modulation and bias currents will be turned
off.
相關PDF資料 |
PDF描述 |
|---|---|
| VSC7938 | Laser Diode Driver with Automatic Power Control |
| VSC7938W | Laser Diode Driver with Automatic Power Control |
| VSC7939 | Laser Diode Driver with Automatic Power Control |
| VSC7939RP | Laser Diode Driver with Automatic Power Control |
| VSC7939W | Laser Diode Driver with Automatic Power Control |
相關代理商/技術參數 |
參數描述 |
|---|---|
| VSC7938W | 制造商:VITESSE 制造商全稱:Vitesse Semiconductor Corporation 功能描述:Laser Diode Driver with Automatic Power Control |
| VSC7939 | 制造商:VITESSE 制造商全稱:Vitesse Semiconductor Corporation 功能描述:Laser Diode Driver with Automatic Power Control |
| VSC7939RP | 制造商:VITESSE 制造商全稱:Vitesse Semiconductor Corporation 功能描述:Laser Diode Driver with Automatic Power Control |
| VSC7939W | 制造商:VITESSE 制造商全稱:Vitesse Semiconductor Corporation 功能描述:Laser Diode Driver with Automatic Power Control |
| VSC7940 | 制造商:VITESSE 制造商全稱:Vitesse Semiconductor Corporation 功能描述:SONET/SDH 3.125Gb/s Laser Diode Driver with Automatic Power Control |
發布緊急采購，3分鐘左右您將得到回復。