- 您現在的位置：買賣IC網 > PDF目錄359428 > VSC7140QJ (VITESSE SEMICONDUCTOR CORP) 1.0625 Gb/s Fibre Channel Dual Repeater / Hub Node PDF資料下載
參數資料
| 型號： | VSC7140QJ |
| 廠商： | VITESSE SEMICONDUCTOR CORP |
| 元件分類： | 通信及網絡 |
| 英文描述： | 1.0625 Gb/s Fibre Channel Dual Repeater / Hub Node |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PQFP52 |
| 封裝： | 10 X 10 MM, PLASTIC, QFP-52 |
| 文件頁數： | 3/12頁 |
| 文件大?。?/td> | 115K |
| 代理商： | VSC7140QJ |
VITESSE
Data Sheet
VSC7140
1.0625 Gb/s Fibre Channel
Dual Repeater / Hub Node
G52180-0, Rev 4.0
10/23/00
Page 3
VITESSE
SEMICONDUCTOR CORPORATION
741 Calle Plano Camarillo, CA 93012
Tel: (800) VITESSE FAX: (805) 987-5896 Email: prodinfo@vitesse.com
Internet: www.vitesse.com
Application Examples
The VSC7140 is intended for two applications, Dual Repeater or Dual Hub, as configured by HUB. Users
needing to retime both incoming and outgoing signals at the bulkhead of a Fibre Channel system would use the
part in Dual Repeater Mode (HUB is LOW). Users building Fibre Channel Hubs would use the part in Dual
Hub mode (HUB is HIGH) to fully handle the functions of two Hub Nodes.
Dual Repeater Mode
In this example, the VSC7140 forms a dual repeater in a complex Fibre Channel system, such as a JBOD
(Just a Bunch Of Disks) RAID (Redundant Array of Independent Disks) subsystem, which requires the incom-
ing Fibre Channel signal to be retimed to ensure adequate signal quality to the input of the subsystem. Like-
wise, the output of the JBOD subsystem requires retiming to ensure that the outgoing signal from the system
meets the amplitude and jitter requirements of Fibre Channel. For this application, the dual CRUs are the only
circuits required although the SDUs may be used for reporting signal status. Therefore, the VSC7140 would be
configured as follows:
HUB is LOW to select Dual Repeater Mode.
RX1 connects to the external input from the bulkhead.
SO1 connects to the input to the JBOD subsystem.
RX2 connects to the output of the JBOD subsystem.
SO2 connects to the output to the bulkhead.
SI1 and SI2 are not used. Pull up SI1+ and SI2+ to V
DD
with 22k Ohms to prevent input oscillations.
TX1 and TX2 are not used. Leave unconnected.
SEL1 and SEL2 are driven HIGH.
FAIL1- and FAIL2- may be used for status. ERRSEL is selected as desired by the user.
Figure 1: Block Diagram: Use of VSC7140 in Dual Repeater Mode
Internal
Fibre Channel
Subsystem
CRU
CRU
VSC7140
C
RX1
SO1
SO2
RX2
相關PDF資料 |
PDF描述 |
|---|---|
| VSC7142 | Dual Repeater/Retimer for Fibre Channel and Gigabit Ethernet |
| VSC7146 | BOX 4.94X2.75X1.275 W/CLP ALMOND |
| VSC7146RH | 2.5Gb/s, 20-Bit Transceiver |
| VSC7147 | Hex PBC with Dual Repeater/Retimer |
| VSC7148 | 16-Port JBOD Loop Chip for 1.0625 Gb/s FC-AL Storage Applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| VSC7140QJ-13 | 制造商:Vitesse Semiconductor Corporation 功能描述: |
| VSC7142 | 制造商:VITESSE 制造商全稱:Vitesse Semiconductor Corporation 功能描述:Dual Repeater/Retimer for Fibre Channel and Gigabit Ethernet |
| VSC7142RC | 功能描述:DUAL REPEATER/RETIMER RoHS:否 類別:集成電路 (IC) >> 接口 - 信號緩沖器，中繼器，分配器 系列:- 標準包裝:160 系列:- 類型:轉發器 Tx/Rx類型:以太網 延遲時間:- 電容 - 輸入:- 電源電壓:2.37 V ~ 2.63 V 電流 - 電源:60mA 安裝類型:表面貼裝 封裝/外殼:64-TQFP 裸露焊盤 供應商設備封裝:64-TQFP-EP（10x10） 包裝:托盤 其它名稱:Q5134101 |
| VSC7145 | 制造商:VITESSE 制造商全稱:Vitesse Semiconductor Corporation 功能描述:Dual Speed 10-bit Serializer/Deserializer |
| VSC7145RU-30 | 制造商:VITESSE 制造商全稱:Vitesse Semiconductor Corporation 功能描述:Dual Speed 10-bit Serializer/Deserializer |
發布緊急采購，3分鐘左右您將得到回復。