- 您現在的位置：買賣IC網 > PDF目錄359417 > VRE3025JS Analog IC PDF資料下載
參數資料
| 型號： | VRE3025JS |
| 英文描述： | Analog IC |
| 中文描述： | 模擬IC |
| 文件頁數： | 4/5頁 |
| 文件大小： | 431K |
| 代理商： | VRE3025JS |
DISCUSSION OF PERFORMANCE
THEORY OF OPERATION
The following discussion refers to the schematic in
figure 2 below. A FET current source is used to bias a
6.3V zener diode. The zener voltage is divided by the
resistor network R1 and R2. This voltage is then applied
to the noninverting input of the operational amplifier which
amplifies the voltage to produce a 2.048V output. The
gain is determined by the resistor networks R3 and R4:
G=1 + R4/R3. The 6.3V zener diode is used because it is
the most stable diode over time and temperature.
The current source provides a closely regulated zener
current, which determines the slope of the references’
voltage vs. temperature function. By trimming the zener
current a lower drift over temperature can be achieved.
But since the voltage vs. temperature function is nonlinear
this compensation technique is not well suited for wide
temperature ranges.
Thaler
compensation network of thermistors and resistors that is
used in the VRE series voltage references. This
proprietary network eliminates most of the nonlinearity in
the voltage vs. temperature function. By adjusting the
slope, Thaler Corporation produces a very stable voltage
over wide temperature ranges.
Corporation
has
developed
a
nonlinear
VRE302-6
FIGURE 2
VRE302-6DS REV. B MAY 2001
This network is less than 2% of the overall network
resistance so it has a negligible effect on long term
stability.
Figure 3 shows the proper connection of the VRE302-6
series voltage references with the optional trim resistor for
initial error. The VRE302-6 reference has the ground
terminal brought out on two pins (pin 4 and pin 7) which
are connected together internally. This allows the user to
achieve greater accuracy when using a socket. Voltage
references have a voltage drop across their power supply
ground pin due to quiescent current flowing through the
contact resistance. If the contact resistance was constant
with time and temperature, this voltage drop could be
trimmed out. When the reference is plugged into a socket,
this source of error can be as high as 20ppm. By
connecting pin 4 to the power supply ground and pin 7 to
a high impedance ground point in the measurement
circuit, the error due to the contact resistance can be
eliminated. If the unit is soldered into place, the contact
resistance is sufficiently small that it does not effect
performance. Pay careful attention to the circuit layout to
avoid noise pickup and voltage drops in the lines.
EXTERNAL CONNECTIONS
FIGURE 3
8
4
6
5
+ V
OUT
2
+ V
IN
VRE302-6
10k
C
1μF
OPTIONAL
NOISE REDUCTION
CAPACITOR
OPTIONAL
FINE TRIM
ADJUSTMENT
3
V
TEMP OUT
7
REF. GND
相關PDF資料 |
PDF描述 |
|---|---|
| VRE3025KD | Analog IC |
| VRE3025KS | Analog IC |
| VRE3025LD | Analog IC |
| VRE3025LS | Analog IC |
| VRE302-6AD | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| VRE3025K | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Low Cost Precision Reference |
| VRE3025KD | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| VRE3025KS | 功能描述:基準電壓& 基準電流 ref +2.5V 1ppm 0/70C RoHS:否 制造商:STMicroelectronics 產品:Voltage References 拓撲結構:Shunt References 參考類型:Programmable 輸出電壓:1.24 V to 18 V 初始準確度:0.25 % 平均溫度系數（典型值）:100 PPM / C 串聯 VREF - 輸入電壓（最大值）: 串聯 VREF - 輸入電壓（最小值）: 分流電流（最大值）:60 mA 最大工作溫度:+ 125 C 封裝 / 箱體:SOT-23-3L 封裝:Reel |
| VRE3025L | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Low Cost Precision Reference |
| VRE3025LD | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
發布緊急采購，3分鐘左右您將得到回復。