- 您現在的位置：買賣IC網 > PDF目錄359407 > VNQ830PEP QUAD CHANNEL HIGH SIDE DRIVER PDF資料下載
參數資料
| 型號： | VNQ830PEP |
| 英文描述： | QUAD CHANNEL HIGH SIDE DRIVER |
| 中文描述： | 四通道高邊驅動器 |
| 文件頁數： | 10/20頁 |
| 文件大?。?/td> | 309K |
| 代理商： | VNQ830PEP |
10/20
VNQ830P
Solution 2: A diode (D
GND
) in the ground line.
A resistor (R
=1k
)
should be inserted in parallel to
D
GND
if the device will be driving an inductive load.
This small signal diode can be safely shared amongst
several different HSD. Also in this case, the presence of
the ground network will produce a shift (
j
600mV) in the
input threshold and the status output values if the
microprocessor ground is not common with the device
ground. This shift will not vary if more than one HSD
shares the same diode/resistor network.
Series resistor in INPUT and STATUS lines are also
required to prevent that, during battery voltage transient,
the current exceeds the Absolute Maximum Rating.
Safest configuration for unused INPUT and STATUS pin
is to leave them unconnected.
LOAD DUMP PROTECTION
D
is necessary (Voltage Transient Suppressor) if the
load dump peak voltage exceeds V
CC
max DC rating. The
same applies if the device will be subject to transients on
the V
line that are greater than the ones shown in the
ISO T/R 7637/1 table.
μ
C I/Os PROTECTION:
If a ground protection network is used and negative
transients are present on the V
line, the control pins will
be pulled negative. ST suggests to insert a resistor (R
prot
)
in line to prevent the
μ
C I/Os pins to latch-up.
The value of these resistors is a compromise between the
leakage current of
μ
C and the current required by the
HSD I/Os (Input levels compatibility) with the latch-up limit
of
μ
C I/Os.
-V
CCpeak
/I
latchup
≤
R
prot
≤
(V
OH
μ
C
-V
IH
-V
GND
) / I
IHmax
Calculation example:
For V
CCpeak
= - 100V and I
latchup
≥
20mA; V
OH
μ
C
≥
4.5V
5k
≤
R
prot
≤
65k
.
Recommended R
prot
value is 10k
.
相關PDF資料 |
PDF描述 |
|---|---|
| VNQ860 | QUAD CHANNEL HIGH SIDE DRIVER |
| VNQ860SP | QUAD CHANNEL HIGH SIDE DRIVER |
| VNS008A | TRANSISTOR | MOSFET | N-CHANNEL | 600V V(BR)DSS | 5.77A I(D) | TO-204AA |
| VNS009A | TRANSISTOR | MOSFET | N-CHANNEL | 600V V(BR)DSS | 5A I(D) | TO-204AA |
| VNT009A | TRANSISTOR | MOSFET | N-CHANNEL | 650V V(BR)DSS | 5A I(D) | TO-204AA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| VNQ830PEP-E | 功能描述:功率驅動器IC Quad Ch HiSide Drivr RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| VNQ830PEPTR-E | 功能描述:功率驅動器IC Quad Ch HiSide Drivr RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| VNQ830PTR-E | 功能描述:功率驅動器IC Quad Ch HiSide Drivr RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| VNQ830TR-E | 功能描述:功率驅動器IC Quad Channel Hi-Side RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| VNQ860 | 功能描述:功率驅動器IC Quad Channel Hi-Side RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。