- 您現在的位置：買賣IC網 > PDF目錄361616 > V18MLA1206H DIODE SUPPRESS SMD BAUFORM 1206 18V PDF資料下載
參數資料
| 型號： | V18MLA1206H |
| 英文描述： | DIODE SUPPRESS SMD BAUFORM 1206 18V |
| 中文描述： | 貼片二極管禁止BAUFORM 1206 18V的 |
| 文件頁數： | 10/12頁 |
| 文件大小： | 87K |
| 代理商： | V18MLA1206H |
5-12
Recommended Pad Outline
Explanation of Terms
Rated DC Voltage (V
M(DC)
)
This is the maximum continuous DC voltage which may be
applied up to the maximum operating temperature of the
device. The rated DC operating voltage (working voltage) is
also used as the reference point for leakage current. This
voltage is always less than the breakdown voltage of the
device.
Rated AC Voltage (V
M(AC)RMS
)
This is the maximum continuous sinusoidal rms voltage
which may be applied. This voltage may be applied at any
temperature up to the maximum operating temperature of
the device.
Maximum Non-Repetitive Surge Current (I
TM
)
This is the maximum peak current which may be applied for
an 8/20
μ
s impulse, with rated line voltage also applied,
without causing device failure. The pulse can be applied to
the device in either polarity with the same confidence factor.
See Figure 2 for waveform description.
Maximum Non-Repetitive Surge Energy (W
TM
)
This is the maximum rated transient energy which may be
dissipated for a single current pulse at a specified impulse
duration (10/1000
μ
s), with the rated DC or RMS voltage
applied, without causing device failure.
Leakage (I
L
) at Rated DC Voltage
In the nonconducting mode, the device is at a very high
impedance (approaching 10
6
at its maximum rated
voltage) and appears essentially as an open circuit in the
system. The leakage current drawn at this level is very low,
as specified in the Device Ratings table.
Nominal Voltage (V
N(DC)
)
This is the voltage at which the device changes from the off
(standby state) to the on (clamping state) and enters its
conduction mode of operation. The voltage value is usually
characterized at the 1mA point and has a specified minimum
and maximum voltage range.
Clamping Voltage (V
C
)
This is the peak voltage appearing across the suppressor
when measured at conditions of specified pulse current and
specified waveform.
Capacitance (C)
This is the capacitance of the device at a specified frequency
(1MHz) and bias (1V
P-P
).
C
B
A
NOTE: Avoid metal runs in this area.
NOTE
SYMBOL
PAD SIZE
FOR 1210
SIZE DEVICE
FOR 1206
SIZE DEVICE
FOR 0805
SIZE DEVICE
FOR 0603
SIZE DEVICE
IN
MM
IN
MM
IN
MM
IN
MM
A
0.219
5.53
0.203
5.15
0.144
3.65
0.11
2.8
B
0.147
3.73
0.103
2.62
0.084
2.13
0.064
1.62
C
0.073
1.85
0.065
1.65
0.058
1.48
0.044
1.12
ML Series
相關PDF資料 |
PDF描述 |
|---|---|
| V18MLA1210H | DIODE SUPPRESS SMD BAUFORM 1210 18V |
| V26MLA1206H | DIODE SUPPRESS SMD BAUFORM 1206 26V |
| V26MLA1210H | DIODE SUPPRESS SMD BAUFORM 1210 26V |
| V3.5MLA0805H | DIODE SUPPRESS SMD BAUFORM 0805 3.5V |
| V42MLA1206H | DIODE SUPPRESS SMD BAUFORM 1206 42V |
相關代理商/技術參數 |
參數描述 |
|---|---|
| V18MLA1206H | 制造商:Littelfuse 功能描述:VARISTOR 1206 18VAC |
| V18MLA1206H23 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| V18MLA1206N | 制造商:LITTELFUSE 制造商全稱:Littelfuse 功能描述:Surface Mount Multilayer Varistors (MLVs) |
| V18MLA1206NA | 功能描述:壓敏電阻 14V 150A 1100pF RoHS:否 制造商:EPCOS 產品:MLV 電壓額定值 DC:22 V 電壓額定值 AC:17 V 鉗位電壓:50 V 直徑: 峰值浪涌電流:30 A 浪涌能量額定值:75 mJ 電容:74.2 pF 工作溫度范圍:- 55 C to + 125 C 安裝:SMD/SMT 封裝:Reel |
| V18MLA1206NH | 功能描述:壓敏電阻 14V 150A 1100pF RoHS:否 制造商:EPCOS 產品:MLV 電壓額定值 DC:22 V 電壓額定值 AC:17 V 鉗位電壓:50 V 直徑: 峰值浪涌電流:30 A 浪涌能量額定值:75 mJ 電容:74.2 pF 工作溫度范圍:- 55 C to + 125 C 安裝:SMD/SMT 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。