ALUMINUM ELECTROLYTIC CAPACITORS
ZP
Plastic platform
Voltage
Capacitance
Voltage mark for 6.3V is 6V .
Lot No.
U
1
Z
2
P
3
1
4
C
5
1
6
0
7
0
8
M
9
C
10
L
11
1
12
G
13
B
14
Configuration
Taping code
Capacitance tolerance (
±
20%)
Rated Capacitance (10
μ
F)
Rated voltage (16V)
Series name
Type
X
1
1
0.3MAX.
4.5
+0.1
φ
D
±
0
B
±
0
C
±
0.2
0
A
±
0
±
0
E
0.5 ~ 0.8
series
4.5mmL Chip Type, Bi-Polarized
Chip type with 4.5mm height.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
Chip Type
Type numbering system (Example : 16V 10
μ
F)
Specifications
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
tan
δ
Stability at Low Temperature
Endurance
Shelf Life
Marking
Performance Characteristics
Item
–40 ~ +85°C
6.3 ~ 50V
0.1 ~ 47μF
±20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.05 CV or 10 (μA) , whichever is greater.
Measurement frequency : 120Hz, Temperature : 20°C
Rated voltage (V)
tan
δ
(MAX.)
0.30
0.24
0.20
Black print on the case top.
Measurement frequency : 120Hz
25
2
4
After 2000 hours' application of rated voltage
at 85°C with the polarity inverted every 250
hours, capacitors meet the characteristic
requirements listed at right.
After storing the capacitors under no load at 85°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above.
The capacitors shall be kept on the hot plate maintained at 250°C
for 30 seconds. After removing from the hot plate and restored
at room temperature,they meet the characteristic requirements
listed at right.
Resistance to soldering
heat
Z P
Z–25°C / Z+20°C
Z–40°C / Z+20°C
Rated voltage (V)
Impedance ratio
ZT / Z20 (MAX.)
6.3
4
8
10
3
8
16
2
4
35
2
3
50
2
3
Dimensions
0.1
0.22
0.33
0.47
1
2.2
3.3
4.7
10
22
33
47
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
5
6.3
6.3
28
37
45
6.3
0J
10
1A
16
1C
25
1E
35
1V
50
1H
V
Code
4
6.3
6.3
17
33
41
4
5
6.3
6.3
12
23
37
49
5
5
6.3
12
16
27
4
5
5
6.3
8.4
16
18
29
4
4
4
4
4
5
5
6.3
1.0
2.0
2.8
4.0
8.4
13
17
20
Rated Ripple (mArms) at 85°C 120Hz
φ
D
A
B
C
E
4
1.8
4.3
4.3
1.0
5
2.1
5.3
5.3
1.3
6.3
2.4
6.6
6.6
2.2
(mm)
Cap. (μF)
6.3
10
16
25
0.18
35
0.16
50
0.16
Capacitance change
tan
δ
Leakage current
Within ±10% of initial value
Initial specified value or less
Initial specified value or less
Capacitance change
tan
δ
Leakage current
Within ±20% of initial value
300% or less of initial specified value
Initial specified value or less
Rated
Frequency coefficient of rated ripple current
Frequency
50 Hz
0.70
Coefficient
120 Hz
1.00
300 Hz
1.17
1 kHz
1.36
10 kHz~
1.50
Taping specifications are given in page 24.
Recommended land size, soldering by reflow are given
in page 25, 26.
Please select WP(p.47), UN(p.77) series if high C/V
products are reqired.
Please refer to page 3 for the minimum order quantity.
CD (mm)
ZE
Smaller
WP
Smaller
CAT.8100V