- 您現在的位置：買賣IC網 > PDF目錄381210 > UT1553B-RTIGCA (Electronic Theatre Controls, Inc.) RTI Remote Terminal Interface PDF資料下載
參數資料
| 型號： | UT1553B-RTIGCA |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | RTI Remote Terminal Interface |
| 中文描述： | RTI的遠程終端接口 |
| 文件頁數： | 10/52頁 |
| 文件大?。?/td> | 1300K |
| 代理商： | UT1553B-RTIGCA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
RTI-10
The following are examples of sequences used to enter
remote terminal addresses into the RTI.
Example 1.
Hardware-Controlled Remote Terminal
Address (parity check disabled):
STATE 0, 2, or 3 (i.e., 00, 10, or 11)
TALEN - asserted (i.e., logic low)
TA(4:0) - valid RTA
Software-Controlled Remote Terminal
Address (parity check disabled):
EXT TEST and EXT TST CH SEL A/B
in STATE 0, 2, or 3 (i.e., 00, 10, or 11)
CTRL - logic zero
CS - logic zero
RD/WR - logic zero
ADDR IN (0) - logic zero
TALEN - logic one
TA(4:0) - valid RTA
Software Controlled Remote Terminal
Address (parity check enabled):
EXT TEST and EXT TST CH SEL A/B
in STATE 1 (i.e., 01)
CTRL - logic zero
CS - logic zero
RD/WR - logic zero
ADDR IN (0) - logic zero
PARITY - input must provide odd
parity
for the TA(4:0) bus
TA(4:0) - valid RTA
For examples 1 and 2, enabling the parity check circuit
(STATE 1) after the remote terminal address is stored results
in a parity check of the data loaded into the Remote Terminal
Address Register.
Example 2.
Example 3.
1.6 Internal Self-Test
Setting bit 6 of the Control Register to a logic one enables
the internal self-test. Disable Channels A and B at this time
to prevent bus activity during self-test by setting bits 0 and
1 of the Control Register to a logic zero. Normal operation
is inhibited when internal self-test is enabled. The RTI’s
self-test capability is based on the fact that the MIL-STD-
1553B status word sync pulse is identical to the command
word sync pulse. Thus, if the status word from the encoder
is fed back to the decoder, the RTI will recognize the
incoming status word as a command word and thus cause
the RTI to transmit another status word. After the host
invokes self-test, the RTI self-test logic forces a status word
transmission even though the RTI has not received a
command word. The status word is sent to decoder A or B
depending on the channel the host selected for self-test. The
host controls the self-test by periodically changing the bit
patterns in the status word being transmitted. Writing to the
Control Register bits 2, 3, 4, and 8 changes the status word.
Monitor the self-test by sampling either the System Register
or the external status pins (i.e. Command Strobe
(COMSTR), Transmit (XMIT), Receive (RCV)). For a more
detailed explanation of internal self-test, consult the UTMC
publication
RTI Internal Self-Test Routine.
1.7 Power-up Master Reset
Reset the RTI by invoking either a hardware or software
master reset after power-up to place the device in a known
state. The master reset clears the decoder and encoder
registers, the command recognition logic, the control and
error logic (which includes the Status, Control and System
Registers), the data transfer logic, and the memory address
control logic. After reset, configure the device for operation
via a Control Register write.
Table 2. Parity Checking
STATE #
0
EXT TEST
0
EXT TST CH SEL A/B
0
Function of TALEN/PARITY
Terminal Address Latch Enable. Active low
signal used to latch TA(4:0) into RTI. Internal
parity checker disabled.
Parity. Internal remote terminal address parity
checker enabled. TALEN/PARITY pin func-
tions as parity bit for TA(4:0) bus. Proper oper-
ation requires odd parity.
Terminal Address Latch Enable. Do not assert
EXT TST during reset, otherwise self-test is
invoked.
Terminal Address Latch Enable. Do not assert
EXT TST during reset, otherwise self-test is
invoked.
1
0
1
2
1
0
3
1
1
相關PDF資料 |
PDF描述 |
|---|---|
| UT1553B-RTIGCC | RTI Remote Terminal Interface |
| UT1553B-RTIGCX | RTI Remote Terminal Interface |
| UT1553B-RTIGPA | RTI Remote Terminal Interface |
| UT1553B-RTIGPC | RTI Remote Terminal Interface |
| UT1553B-RTIGPX | RTI Remote Terminal Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UT1553BRTIGCC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:RTI Remote Terminal Interface |
| UT1553B-RTIGCC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:RTI Remote Terminal Interface |
| UT1553BRTIGCX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:RTI Remote Terminal Interface |
| UT1553B-RTIGCX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:RTI Remote Terminal Interface |
| UT1553BRTIGCXA | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:RTI Remote Terminal Interface |
發布緊急采購，3分鐘左右您將得到回復。