- 您現在的位置：買賣IC網 > PDF目錄381205 > US3011CW (Unisem Group) 5 BIT PROGRAMMABLE SYNCHRONOUS BUCK CONTROLLER IC PDF資料下載
參數資料
| 型號： | US3011CW |
| 廠商： | Unisem Group |
| 英文描述： | 5 BIT PROGRAMMABLE SYNCHRONOUS BUCK CONTROLLER IC |
| 中文描述： | 5位可編程同步降壓控制器芯片 |
| 文件頁數： | 11/11頁 |
| 文件大小： | 72K |
| 代理商： | US3011CW |
US3011
4-11
Rev. 1.3
12/8/00
Layout Considerations
Switching regulators require careful attention to the lay-
out of the components, specifically power components
since they switch large currents. These switching com-
ponents can create large amount of voltage spikes and
high frequency harmonics if some of the critical compo-
nents are far away from each other and are connected
with inductive traces. The following is a guideline of how
to place the critical components and the connections
between them in order to minimize the above issues.
Start the layout by first placing the power components:
1) Place the input capacitors C3 and the high side
mosfet ,Q1 as close to each other as possible
2) Place the synchronous mosfet,Q2 and the Q1 as
close to each other as possible with the intention that
the source of Q1 and drain of the Q2 has the shortest
length.
3) Place the snubber R4 & C7 between Q1 & Q2.
4) Place the output inductor ,L2 and the output capaci-
tors ,C10 between the mosfet and the load with output
capacitors distributed along the slot 1 and close to it.
5) Place the bypass capacitors, C6 and C9 right next to
12V and 5V pins. C6 next to the 12V, pin 18 and C9
next to the 5V, pin 9.
6) Place the IC such that the pwm output drives, pins
14 and 17 are relatively short distance from gates of Q1
and Q2.
7) If the ouput voltage is to be adjusted, place resistor
dividers close to the feedback pin.
Note 1: Although, the device does not require resistor
dividers and the feedback pin can be directly connected
to the output, they can be used to set the outputs slightly
higher to account for any output drop at the load due to
the trace resistance. See the application note.
8) Place timing capacitor C7 close to pin20 and soft
start capacitor C2 close to pin 3.
Component connections:
Note : It is extremely important that no data bus
should be passing through the switching regulator
section specifically close to the fast transition nodes
such as PWM drives or the inductor voltage.
Using 4 layer board, dedicate on layer to GND, another
layer as the power layer for the 5V, 3.3V and Vcore.
Connect all grounds to the ground plane using di-
rect vias to the ground plane.
Use large low inductance/low impedance plane to con-
nect the following connections either using component
side or the solder side.
a) C3 to Q1 Drain
b) Q1 Source to Q2 Drain
c) Q2 drain to L2
d) L2 to the output capacitors, C10
e) C10 to the slot 1
f) Input filter L1 to the C3
Connect the rest of the components using the shortest
connection possible
相關PDF資料 |
PDF描述 |
|---|---|
| US3012 | 5 BIT PROGRAMMABLE SYNCHRONOUS BUCK CONTROLLER IC |
| US3012ACW | 5 BIT PROGRAMMABLE SYNCHRONOUS BUCK CONTROLLER IC |
| US3012CW | 5 BIT PROGRAMMABLE SYNCHRONOUS BUCK CONTROLLER IC |
| US3018 | 5 BIT PROGRAMMABLE SYNCHRONOUS BUCK PLUS LDO CONTROLLER AND 200mA LDO ON BOARD |
| US3018CW | 5 BIT PROGRAMMABLE SYNCHRONOUS BUCK PLUS LDO CONTROLLER AND 200mA LDO ON BOARD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| US3012 | 制造商:UNISEM 制造商全稱:UNISEM 功能描述:5 BIT PROGRAMMABLE SYNCHRONOUS BUCK CONTROLLER IC |
| US-3012 | 功能描述:PROTO-BOARD 12PIN THRU-HOLE SIP RoHS:是 類別:原型開發產品 >> 適配器，可互換接口板 系列:3000, UNI-SIP™ 標準包裝:1 系列:- 原型板類型:- Package Accepted:- 尺寸/尺寸:- 位置數:- 孔直徑:- 板厚度:- 材質:- |
| US3012ACW | 制造商:UNISEM 制造商全稱:UNISEM 功能描述:5 BIT PROGRAMMABLE SYNCHRONOUS BUCK CONTROLLER IC |
| US3012CW | 制造商:UNISEM 制造商全稱:UNISEM 功能描述:5 BIT PROGRAMMABLE SYNCHRONOUS BUCK CONTROLLER IC |
| US-3014 | 功能描述:PROTO-BOARD 14PIN THRU-HOLE SIP RoHS:是 類別:原型開發產品 >> 適配器，可互換接口板 系列:3000, UNI-SIP™ 標準包裝:1 系列:- 原型板類型:- Package Accepted:- 尺寸/尺寸:- 位置數:- 孔直徑:- 板厚度:- 材質:- |
發布緊急采購，3分鐘左右您將得到回復。