參數資料
型號: UPD78F4216AYGC-8EU
廠商: NEC Corp.
英文描述: ER 1C 1#12 PIN PLUG
中文描述: 馬鞍山集成電路
文件頁數: 58/60頁
文件大?。?/td> 349K
代理商: UPD78F4216AYGC-8EU
Data Sheet U14125EJ1V0DS00
58
μ
PD78F4216A, 78F4218A, 78F4216AY, 78F4218AY
NOTES FOR CMOS DEVICES
1
PRECAUTION AGAINST ESD FOR SEMICONDUCTORS
Note:
Strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and
ultimately degrade the device operation. Steps must be taken to stop generation of static electricity
as much as possible, and quickly dissipate it once, when it has occurred. Environmental control
must be adequate. When it is dry, humidifier should be used. It is recommended to avoid using
insulators that easily build static electricity. Semiconductor devices must be stored and transported
in an anti-static container, static shielding bag or conductive material. All test and measurement
tools including work bench and floor should be grounded. The operator should be grounded using
wrist strap. Semiconductor devices must not be touched with bare hands. Similar precautions need
to be taken for PW boards with semiconductor devices on it.
2
HANDLING OF UNUSED INPUT PINS FOR CMOS
Note:
No connection for CMOS device inputs can be cause of malfunction. If no connection is provided
to the input pins, it is possible that an internal input level may be generated due to noise, etc., hence
causing malfunction. CMOS devices behave differently than Bipolar or NMOS devices. Input levels
of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry. Each unused
pin should be connected to V
DD
or GND with a resistor, if it is considered to have a possibility of
being an output pin. All handling related to the unused pins must be judged device by device and
related specifications governing the devices.
3
STATUS BEFORE INITIALIZATION OF MOS DEVICES
Note:
Power-on does not necessarily define initial status of MOS device. Production process of MOS
does not define the initial operation status of the device. Immediately after the power source is
turned ON, the devices with reset function have not yet been initialized. Hence, power-on does
not guarantee out-pin levels, I/O settings or contents of registers. Device is not initialized until the
reset signal is received. Reset operation must be executed immediately after power-on for devices
having reset function.
IEBus is a trademark of NEC Corporation.
Windows is either a registered trademark or a trademark of Microsoft Corporation in the United States and/or
other countries.
PC/AT is a trademark of International Business Machines Corporation.
HP9000 series 700 and HP-UX are trademarks of Hewlett-Packard Company.
SPARCstation is a trademark of SPARC International, Inc.
Solaris and SunOS are trademarks of Sun Microsystems, Inc.
NEWS and NEWS-OS are trademarks of Sony Corporation.
相關PDF資料
PDF描述
UPD78F4216AYGF-3BA MOS INTEGRATED CIRCUIT
UPD78F4216AGC-8EU MOS INTEGRATED CIRCUIT
UPD9930 LINEAR CODEC FOR DIGITAL CELLULAR TELEPHONE
UPD9930G-22 LINEAR CODEC FOR DIGITAL CELLULAR TELEPHONE
UPG103B CONNECTOR ACCESSORY
相關代理商/技術參數
參數描述
UPD78F4216AYGF-3BA 制造商:Renesas Electronics Corporation 功能描述:
UPD78F4218AGC-8EU 制造商:Renesas Electronics Corporation 功能描述:
UPD78F4218AGC-8EU-A 制造商:Renesas Electronics Corporation 功能描述:
UPD78F4218AYGC-8EU-A 制造商:Renesas Electronics Corporation 功能描述:MCU 16BIT 78K4 CISC 256KB FLASH 2.5V/3.3V/5V 100LQFP - Trays
UPD78F4218AYGF-3BA-A 制造商:Renesas Electronics Corporation 功能描述: