- 您現在的位置：買賣IC網 > PDF目錄376434 > UPD75P036 (NEC Corp.) 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER PDF資料下載
參數資料
| 型號： | UPD75P036 |
| 廠商： | NEC Corp. |
| 元件分類： | 4位微控制器 |
| 英文描述： | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| 中文描述： | 4位單片機的小型通用紅外遙控器 |
| 文件頁數： | 36/40頁 |
| 文件大?。?/td> | 320K |
| 代理商： | UPD75P036 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁
36
μ
PD75P048
8. RECOMMENDED SOLDERING CONDITIONS
It is recommended that
μ
PD75P048 be soldered under the following conditions. For details on the recommended
soldering conditions, refer to Information Document "Semiconductor Devices Mounting Manual" (IEI-1207). For
other soldering methods and conditions, consult NEC.
Table 8-1 Soldering Conditions of Surface-Mount Type
μ
PD75P048GC-AB8: 64-pin plastic QFP (
14 mm)
Soldering Method
Soldering Conditions
Symbol for Recommended
Condition
IR35-00-2
Infrared Reflow
Package peak temperature: 235
°
C,
time: 30 seconds max. (210
°
C min.),
number of times: 2 max.
<Caution>
(1) Start second reflow after device temperature
(which has risen because of first reflow) has returned to
room temperature.
(2) Do not clean flux with water after first reflow.
Package peak temperature: 215
°
C,
time: 40 seconds max. (200
°
C min.),
number of times: 1 max.
<Caution>
(1) Start second reflow after device temperature
(which has risen because of first reflow) has returned to
room temperature.
(2) Do not clean flux with water after first reflow.
Pin temperature: 300
°
C max.,
time: 3 seconds max. (per side)
VPS
VP15-00-2
Pin Partial Heating
—
Caution Do not use two or more soldering methods in combination (except the pin partial heating method).
Table 8-2 Soldering Conditions of Through-Hole Type
μ
PD75P048CW: 64-pin plastic shrink DIP (750 mil)
Soldering Method
Wave soldering
(lead parts only)
Pin Partial Heating
Soldering Conditions
Soldering bath temperature: 260
°
C max.,
time: 10 seconds max.,
Pin temperature: 260
o
C max.,
time: 10 seconds max.
Caution The wave soldering must be performed at the lead part only. Note that the soldering must not be
directly contacted to the board.
#
相關PDF資料 |
PDF描述 |
|---|---|
| UPD75P036CW | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| UPD75P036KG | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| UPD75P048 | 4-BIT SINGLE-CHIP MICROCOMPUTER |
| UPD75P068 | 4 BIT SINGLE-CHIP MICROCOMPUTER |
| UPD75P068CU | 4 BIT SINGLE-CHIP MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UPD75P3018AGC-8BT-A | 制造商:Renesas Electronics Corporation 功能描述:MCU 4BIT 75XL CISC 32KB EPROM 2.5V/3.3V/5V 80PQFP - Trays 制造商:Renesas Electronics 功能描述:75XL 6MHz Cut Tape 制造商:Renesas 功能描述:MCU 4-bit 75XL CISC 32KB EPROM 2.5V/3.3V/5V 80-Pin PQFP |
| UPD75P3018AGK-BE9 | 制造商:Renesas Electronics Corporation 功能描述: |
| UPD75P3036GC-3B9-A | 制造商:Renesas Electronics Corporation 功能描述: |
| UPD75P308GF-3B9 | 制造商:Renesas Electronics Corporation 功能描述:MCU 4-Bit 75XL CISC 8064Byte PROM 5V 80-Pin PQFP |
| UPD75P308GF-3BA | 制造商:Renesas Electronics Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。