參數資料
型號： UPD65650-QFP136P1.2SQ
英文描述： ASIC
中文描述： 專用集成電路
文件頁數： 23/64頁
文件大?。?/td> 399K
代理商： UPD65650-QFP136P1.2SQ
23
μ
PD64A, 65
Data Sheet U14380EJ2V0DS00
5.2 Standby Mode Setup and Release
The standby mode is set with the HALT #b
3
b
2
b
1
b
0
B instruction for both STOP mode and HALT mode. For the
standby mode to be set, the status flag (F) is required to have been cleared (to 0).
The standby mode is released by the release condition specified with the reset (POC) or the operand of HALT
instruction. If the standby mode is released, the status flag (F) is set (to 1).
Even when the HALT instruction is executed in the state that the status flag (F) has been set (to 1), the standby
mode is not set. If the release condition is not met at this time, the status flag is cleared (to 0). If the release condition
is met, the status flag remains set (to 1).
Even in the case when the release condition has been already met at the point that the HALT instruction is
executed, the standby mode is not set. Here, also, the status flag (F) is set (to 1).
Caution Depending on the status of the status flag (F), the HALT instruction may not be executed. Be
careful about this. For example, when setting HALT mode after checking the key status with
the STTS instruction, the system does not enter HALT mode as long as the status flag (F)
remains set (to 1) thus sometimes performing an unintended operation. In this case, the
intended operation can be realized by executing the STTS instruction immediately after timer
setting to clear (to 0) the status flag.
Example
STTS
#03H
;To check the K
I
pin status.
MOV
STTS
T, #0xxH
#05H
(During this time, be sure not to execute an instruction that may set the status flag.)
#05H
;To set HALT mode
;To set the timer
;To clear the status flag
HALT
Table 5-2. Addresses Executed after Standby Mode Release
Release Condition
Address Executed after Release
Reset
0 address
Release condition shown in Table 5-3
The address following the HALT instruction
…
…
相關PDF資料
PDF描述
UPD65650-QFP160P1.2SQ ASIC
UPD65654-QFP100P.63SQ ASIC
UPD65654-QFP100P.7X.9 ASIC
UPD65654-QFP120P1.2SQ ASIC
UPD65654-QFP136P1.2SQ ASIC
相關代理商/技術參數
參數描述
UPD65650-QFP160P1.2SQ 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ASIC
UPD65651 制造商:NEC 制造商全稱:NEC 功能描述:CMOS-6/6A/6V/6X 1.0-MICRON CMOS GATE ARRAYS
UPD65652 制造商:NEC 制造商全稱:NEC 功能描述:CMOS-6/6A/6V/6X 1.0-MICRON CMOS GATE ARRAYS
UPD65654 制造商:NEC 制造商全稱:NEC 功能描述:CMOS-6/6A/6V/6X 1.0-MICRON CMOS GATE ARRAYS
UPD65654GF-252-3B9 制造商:Renesas Electronics Corporation 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*