- 您現在的位置：買賣IC網 > PDF目錄378742 > UPD6456GS-101 On-Screen Display Circuit PDF資料下載
參數資料
| 型號： | UPD6456GS-101 |
| 英文描述： | On-Screen Display Circuit |
| 中文描述： | 屏幕顯示電路 |
| 文件頁數： | 23/68頁 |
| 文件大?。?/td> | 301K |
| 代理商： | UPD6456GS-101 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
23
μ
PD63, 63A, 64
5.2 Standby Mode Setup and Release
The standby mode is set with the HALT #b
3
b
2
b
1
b
0
B instruction for both STOP mode and HALT mode. For the
standby mode to be set, the status flag (F) is required to have been cleared (to 0).
The standby mode is released by the release condition specified with the RESET (RESET input; POC) or the
operand of HALT instruction. If the standby mode is released, the status flag (F) is set (to 1).
Even when the HALT instruction is executed in the state that the status flag (F) has been set (to 1), the standby
mode is not set. If the release condition is not met at this time, the status flag is cleared (to 0). If the release condition
is met, the status flag remains set (to 1).
Even in the case when the release condition has been already met at the point that the HALT instruction is
executed, the standby mode is not set. Here, also, the status flag (F) is set (to 1).
Caution Depending on the status of the status flag (F), the HALT instruction may not be executed. Be
careful about this. For example, when setting HALT mode after checking the key status with
the STTS instruction, the system does not enter HALT mode as long as the status flag (F)
remains set (to 1) thus sometimes performing an unintended operation. In this case, the
intended operation can be realized by executing the STTS instruction immediately after timer
setting to clear (to 0) the status flag.
Example
STTS
#03H
;To check the K
I
pin status.
MOV
STTS
T, #0xxH
#05H
(During this time, be sure not to execute an instruction that may set the status flag.)
#05H
;To set HALT mode
;To set the timer
;To clear the status flag
HALT
Table 5-2. Addresses Executed After Standby Mode Release
Release Condition
Address Executed After Release
Reset
0 address
Release condition shown in Table 5-3
The address following the HALT instruction
…
…
相關PDF資料 |
PDF描述 |
|---|---|
| UPD6456GS-102 | On-Screen Display Circuit |
| UPD6456GS-103 | MARS TRANSCEIVER MODULE |
| UPD6460GT-101 | On-Screen Display Circuit |
| UPD65MC-XXX-5A4 | MICROCONTROLLER|4-BIT|CMOS|SSOP|20PIN|PLASTIC |
| UPD64GS | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR INFRARED REMOTE CONTROL TRANSMISSION |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UPD6456GS-102 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:On-Screen Display Circuit |
| UPD6456GS-103 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:On-Screen Display Circuit |
| UPD6460G-601 | 制造商:Panasonic Industrial Company 功能描述:IC |
| UPD6460G-605 | 制造商:Panasonic Industrial Company 功能描述:IC |
| UPD6460GT-101 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:On-Screen Display Circuit |
發布緊急采購，3分鐘左右您將得到回復。