- 您現在的位置：買賣IC網 > PDF目錄378738 > UPD6134 (NEC Corp.) 4-BIT SINGLE-CHIP MICROCONTROLLER FOR INFRARED REMOTE CONTROL TRANSMISSION PDF資料下載
參數資料
| 型號： | UPD6134 |
| 廠商： | NEC Corp. |
| 英文描述： | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR INFRARED REMOTE CONTROL TRANSMISSION |
| 中文描述： | 4位單片機的紅外遙控傳輸 |
| 文件頁數： | 26/64頁 |
| 文件大?。?/td> | 410K |
| 代理商： | UPD6134 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
26
μ
PD6133, 6134
Data Sheet U10454EJ6V0DS00
6. RESET PIN
The system reset takes effect by inputting low level to the RESET pin.
While the RESET pin is at low level, the system clock oscillator is stopped and the X
IN
and X
OUT
pins are fixed
to the GND.
If the RESET pin is raised from low level to high level, it executes the program from the 0 address after counting
60 to 116 of the system clock (f
X
).
Figure 6-1. Reset Operation by RESET Input
Wait
(60 to 116)/f
X
+
α
HALT mode
Oscillation
stopped
OPERATING mode or
STANDBY mode
RESET
0 address start
α
: Oscillation growth time
OPERATING
mode
The RESET pin outputs low level when the POC circuit (mask option) is in operation.
Caution When connecting a reset IC to the RESET pin, ensure that the IC is of the N-ch open drain output
type.
Table 6-1. Hardware Statuses After Reset
RESET Input in Operation
Resetting by Internal POC Circuit in Operation
Resetting by Other Factors
Note 1
RESET Input During STANDBY Mode
Resetting by the Internal POC Circuit During
STANDBY Mode
Hardware
PC (10 bits)
000H
SP (1 bit)
0B
Data
R0 = DP
000H
memory
R1-RF
Undefined
Previous status retained
Accumulator (A)
Undefined
Status flag (F)
0B
Carry flag (CY)
0B
Timer (10 bits)
000H
Port register
P0
FFH
P1
×
FH
Note 2
Control register P3
03H
P4
26H
Notes 1.
The following resets are available.
Reset when executing the HALT instruction (when the operand value is illegal or does not satisfy
the precondition)
Reset when executing the RLZ instruction (when A = 0)
Reset by stack pointer’s overflow or underflow
2.
Refers to the value by the K
I
pin status.
In order to prevent malfunction, be sure to input a low level to more than one of pins K
I0
to K
I3
when
reset is released (when RESET pin changes from low level to high level, or POC is released due to
supply voltage startup).
相關PDF資料 |
PDF描述 |
|---|---|
| UPD6134GS | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR INFRARED REMOTE CONTROL TRANSMISSION |
| UPD6134MC | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR INFRARED REMOTE CONTROL TRANSMISSION |
| UPD61P24 | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR REMOTE CONTROL TRANSMISSION |
| UPD61012 | Consumer IC |
| UPD6102G | Consumer IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UPD6134GS | 制造商:NEC 制造商全稱:NEC 功能描述:4-BIT SINGLE-CHIP MICROCONTROLLER FOR INFRARED REMOTE CONTROL TRANSMISSION |
| UPD6134GS-XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Bit Microcontroller |
| UPD6134MC | 制造商:NEC 制造商全稱:NEC 功能描述:4-BIT SINGLE-CHIP MICROCONTROLLER FOR INFRARED REMOTE CONTROL TRANSMISSION |
| UPD6140C | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Peripheral IC |
| UPD6140G | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Peripheral IC |
發布緊急采購，3分鐘左右您將得到回復。