- 您現在的位置：買賣IC網 > PDF目錄378738 > UPD6133 (NEC Corp.) 4-BIT SINGLE-CHIP MICROCONTROLLER FOR INFRARED REMOTE CONTROL TRANSMISSION PDF資料下載
參數資料
| 型號： | UPD6133 |
| 廠商： | NEC Corp. |
| 英文描述： | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR INFRARED REMOTE CONTROL TRANSMISSION |
| 中文描述： | 4位單片機的紅外遙控傳輸 |
| 文件頁數： | 20/64頁 |
| 文件大?。?/td> | 410K |
| 代理商： | UPD6133 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
20
μ
PD6133, 6134
Data Sheet U10454EJ6V0DS00
4.2 Timer Operation
The timer starts (counting down) when a value other than 0 is set for the down counter with a timer operation
instruction. The timer operation instructions for making the timer start operation are shown below:
MOV T0, A
MOV T1, A
MOV T, #data10
MOV T, @R0
The down counter is decremented (–1) in the cycle of 8/f
X
or 16/f
X
Note
. If the value of the down counter becomes
0, the zero detecting circuit generates the timer operation end signal to stop the timer operation. At this time, if
the timer is in HALT mode (HALT #
×
101B) waiting for the timer to stop its operation, the HALT mode is canceled
and the instruction following the HALT instruction is executed. The output of the timer operation end signal is
continued while the down counter is 0 and the timer is stopped. There is the following relational expression between
the timer’s time and the down counter’s set value.
Timer time = (Set value + 1)
×
8/f
X
(or 16/f
X
Note
)
Note
This becomes 16/f
X
if bit 3 of the control register is set (to 1).
By setting 1 for the flag (t
9
) which enables the timer output, the timer can output its operation status from the
S
1
/LED pin and the REM pin. The REM pin can also output the carrier while the timer is in operation.
Table 4-1. Timer Output (at t
9
= 1)
S
1
/LED Pin
REM Pin
Timer operating
L
H (or carrier output
Note
)
Timer halting
H
L
Note
The carrier output results if bit 2 of the control register 0 is cleared (to 0).
Figure 4-2. Timer Output (When Carrier Is Not Output)
Timer value: (Set value + 1)
×
8 f/
X
(or 16/f
X
)
LED
REM
相關PDF資料 |
PDF描述 |
|---|---|
| UPD6133GS | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR INFRARED REMOTE CONTROL TRANSMISSION |
| UPD6134 | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR INFRARED REMOTE CONTROL TRANSMISSION |
| UPD6134GS | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR INFRARED REMOTE CONTROL TRANSMISSION |
| UPD6134MC | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR INFRARED REMOTE CONTROL TRANSMISSION |
| UPD61P24 | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR REMOTE CONTROL TRANSMISSION |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UPD6133GS | 制造商:NEC 制造商全稱:NEC 功能描述:4-BIT SINGLE-CHIP MICROCONTROLLER FOR INFRARED REMOTE CONTROL TRANSMISSION |
| UPD6133GS-XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Bit Microcontroller |
| UPD6134 | 制造商:NEC 制造商全稱:NEC 功能描述:4-BIT SINGLE-CHIP MICROCONTROLLER FOR INFRARED REMOTE CONTROL TRANSMISSION |
| UPD6134GS | 制造商:NEC 制造商全稱:NEC 功能描述:4-BIT SINGLE-CHIP MICROCONTROLLER FOR INFRARED REMOTE CONTROL TRANSMISSION |
| UPD6134GS-XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。