- 您現在的位置：買賣IC網 > PDF目錄378738 > UPD6120C-102 Remote-Control Transmitter/Encoder PDF資料下載
參數資料
| 型號： | UPD6120C-102 |
| 英文描述： | Remote-Control Transmitter/Encoder |
| 中文描述： | 遠程控制發射機/編碼器 |
| 文件頁數： | 19/36頁 |
| 文件大?。?/td> | 252K |
| 代理商： | UPD6120C-102 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
μ
PD61P24
19
17.2 Program Memory Writing Procedure
The program memory is written at high speed in the following procedure.
(1) Pull down the pins not used to GND via resistor. Keep the CLK pin low.
(2) Supply 5 V to the V
DD
pin. Keep the V
PP
pin low.
(3) Wait for 10
μ
s, and supply 5 V to the V
PP
pin.
(4) Set the mode in which the program memory address is cleared to 0, by using the mode setting pins.
(5) Supply 6 V to V
DD
and 12.5 V to V
PP
.
(6) Set the program inhibit mode.
(7) Write data in the 1-ms write mode.
(8) Set the program inhibit mode.
(9) Set the verify mode. If the data has been correctly written, proceed to (10). If not, repeat (7) through (9).
(10) Additional writing of (Number of times data has been written in (7) through (9): X)
×
1 ms
(11) Set the program inhibit mode.
(12) Input a pulse four times to the CLK pin to update the program memory address (+1).
(13) Repeat (7) through (12) until the data is written to the last address.
(14) Set the mode in which the program memory address is cleared to 0.
(15) Change the voltage on the V
DD
and V
PP
pins to 5 V.
(16) Turn off power supply.
Program memory writing steps (2) through (12) are illustrated below.
Write
Verify
Additional write
Address
increment
Repeat X times
MD3
MD2
MD1
MD0
D0-D7
CLK
GND
V
DD
V
DD
V
DD
+1
GND
V
DD
V
PP
V
PP
Data input
Data output
Data input
Hi-Z
Hi-Z
Hi-Z
Hi-Z
Reset
相關PDF資料 |
PDF描述 |
|---|---|
| UPD6127CS | Remote-Control Transmitter/Encoder |
| UPD6127GS | Remote-Control Transmitter/Encoder |
| UPD6129CS | Remote-Control Transmitter/Encoder |
| UPD6129GS | Remote-Control Transmitter/Encoder |
| UPD6130CA-002 | Remote-Control Transceiver/Endec |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UPD6121 | 制造商:NEC 制造商全稱:NEC 功能描述:REMOTE CONTROL TRANSMISSION CMOS IC |
| UPD6121G-001 | 制造商:NEC 制造商全稱:NEC 功能描述:REMOTE CONTROL TRANSMISSION CMOS IC |
| UPD6121G-002 | 制造商:NEC 制造商全稱:NEC 功能描述:REMOTE CONTROL TRANSMISSION CMOS IC |
| UPD6122 | 制造商:NEC 制造商全稱:NEC 功能描述:REMOTE CONTROL TRANSMISSION CMOS IC |
| UPD6122G-001 | 制造商:NEC 制造商全稱:NEC 功能描述:REMOTE CONTROL TRANSMISSION CMOS IC |
發布緊急采購，3分鐘左右您將得到回復。