- 您現在的位置：買賣IC網 > PDF目錄379494 > UPD17226MC (NEC Corp.) 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER PDF資料下載
參數資料
| 型號： | UPD17226MC |
| 廠商： | NEC Corp. |
| 元件分類： | 4位微控制器 |
| 英文描述： | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| 中文描述： | 4位單片機的小型通用紅外遙控器 |
| 文件頁數： | 41/84頁 |
| 文件大小： | 393K |
| 代理商： | UPD17226MC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
μ
PD17225, 17226, 17227, 17228
41
Data Sheet U12643EJ2V0DS00
7.2
Hardware of Interrupt Control Circuit
This section describes the flags of the interrupt control circuit.
(1)
Interrupt request flag and interrupt enable flag
The interrupt request flag (IRQ
×××
) is set to 1 when an interrupt request is generated, and is automatically
cleared to 0 when the interrupt processing is excuted.
An interrupt enable flag (IP
×××
) is provided to each interrupt request flag. When the IPxxx flag is 1, the interrupt
is enabled; when it is 0, the interrupt is disabled.
(2)
EI/DI instruction
Whether an accepted interrupt is executed or not is specified by the EI or DI instruction.
When the EI instruction is executed, INTE (interrupt enable flag), which enables the interrupt, is set to 1. The
INTE flag is not registered on the register file. Consequently, the status of this flag cannot be checked by
an instruction.
The DI flag clears the INTE flag to 0 to disable all the interrupts.
The INTE flag is also cleared to 0 at reset, disabling all the interrupts.
Table 7-2. Interrupt Request Flags and Interrupt Enable Flag
Interrupt
Request Flag
Signal Setting Interrupt Request Flag
Interrupt
Enable Flag
IRQTM
Reset by 8-bit timer.
IPTM
IRQ
Set when edge of INT pin input signal is detected
IP
IRQBTM
Reset by basic interval timer.
IPBTM
7.2.1
INT
This flag reads the INT pin status.
When a high level is input to the INT pin, this flag is set to “1”; when a low level is input, the flag is reset to “0”.
3
2
1
0
0
0
0
INT
Address
RF : 0FH
INT
On reset
Undefined
R/W
R
0
1
INT Pin Level Detection
INT pin : Low level
INT pin : High level
相關PDF資料 |
PDF描述 |
|---|---|
| UPD17227 | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| UPD17227CT | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| UPD17227MC | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| UPD17228 | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| UPD17228CT | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UPD17226MC-XXX-5A4 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| UPD17227 | 制造商:NEC 制造商全稱:NEC 功能描述:4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| UPD17227CT | 制造商:NEC 制造商全稱:NEC 功能描述:4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| UPD17227CT-XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Bit Microcontroller |
| UPD17227GT | 制造商:NEC 制造商全稱:NEC 功能描述:4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
發布緊急采購，3分鐘左右您將得到回復。