- 您現在的位置：買賣IC網 > PDF目錄361551 > UM0231 (意法半導體) User manual AD-ICD in-circuit debugging adapter PDF資料下載
參數資料
| 型號： | UM0231 |
| 廠商： | 意法半導體 |
| 英文描述： | User manual AD-ICD in-circuit debugging adapter |
| 中文描述： | 用戶手冊廣告ICD的在線調試適配器 |
| 文件頁數： | 5/15頁 |
| 文件大小： | 454K |
| 代理商： | UM0231 |
AD-ICD
2 Configuring the ICD adapter
5/15
2
Configuring the ICD adapter
The following sections provide instructions about configuring your ICD adapter for
In-circuit
debugging
or to
Run the application in standalone mode
. Delivered from the factory, the AD-
ICD/DS8Z-01 is configured as follows:
Caution:
When configuring the ICD adapter, make sure that the ICD tool and application board (if
connected to the adapter) are powered off.
2.1
In-circuit debugging
ICD On jumper (TP1)
When in-circuit debugging the target application via the 10-pin ICC connection, the
ICD On
jumper (TP1) must be fitted to allow the interface with an in-circuit debugging tool and the
host PC. During in-circuit debugging, the RST/PA3 On jumper (TP2) must not be fitted.
Table 1.
Default configuration of the AD-ICD/DS8Z-01 from factory
Identifier on
ICD adapter
Configuration
Purpose
Jumpers
TP1
Fitted
Allow connection for in-circuit
debugging/programming
TP2
Not fitted
Run application in standalone mode
Solder points
G1
Soldered
Connects tool to the microcontroller’s VDD pin
(accommodate tools with a power supply
follower)
G2
Not soldered
Connect tool’s clock signal to microcontroller’s
CLKIN pin
Figure 3.
ICD On jumper (TP1)
To set the
ICD On
jumper (TP1):
1.
Make sure the in-circuit debugging tool
and the application are powered off.
2.
Place the jumper on
TP1
as shown in
Figure 3
.
3.
Connect to and power on the in-circuit
debugging tool and application board.
Refer to the on-line help of your integrated
development environment/debugging
software for further information about in-
circuit programming and debugging the
microcontroller on the ICD adapter.
TP1
fitted for ICD
TP2 not fitted
for ICD
MB509
相關PDF資料 |
PDF描述 |
|---|---|
| UM0462 | STM32F101xx and STM32F103xx Flash loader demonstrator |
| UM104 | ST7262 - LOW SPEED USB 8-BIT MCU WITH 3 ENDPOINTS, FLASH OR ROM MEMORY, LVD, WDG, 10-BIT ADC, 2 TIMERS, SCI, SPI |
| UM101 | AC LINE SWITCH |
| UM101M | Single bilateral switch |
| UM102 | 16-bit low voltage ROMless MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UM0404-0250Q-01B | 制造商:Malico, Inc. 功能描述:USB & Mini-DIN Cable with Bracket, Bulk |
| UM0462 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:STM32F101xx and STM32F103xx Flash loader demonstrator |
| UM0470 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:STM8 SWIM communication protocol and debug module |
| UM1 | 制造商:GOLLEDGE 制造商全稱:GOLLEDGE 功能描述:Miniature Crystals |
| UM-1 | 制造商:EUROQUARTZ 制造商全稱:EUROQUARTZ limited 功能描述:Frequency range 1.0MHz to 200MHz High-precision crystal ideal for telecoms applications |
發布緊急采購，3分鐘左右您將得到回復。