參數資料
型號: UGS3059KA
廠商: Allegro MicroSystems, Inc.
英文描述: HALL-EFFECT GEAR-TOOTH SENSORS -AC COUPLED
中文描述: 霍爾效應齒輪齒傳感器交流耦合
文件頁數: 1/10頁
文件大小: 144K
代理商: UGS3059KA
The UGS3059KA and UGN/UGS3060KA ac-coupled Hall-effect
gear-tooth sensors are monolithic integrated circuits that switch in
response to changing differential magnetic fields created by moving
ferrous targets. These devices are ideal for use in non-zero-speed,
gear-tooth-based speed, position, and timing applications such as in
anti-lock braking systems, transmissions, and crankshafts.
Both devices, when coupled with a back-biasing magnet, can be
configured to turn ON or OFF with the leading or trailing edge of a
gear-tooth or slot. Changes in fields on the magnet face caused by a
moving ferrous mass are sensed by two integrated Hall transducers
and are differentially amplified by on-chip electronics. This differential
sensing design provides immunity to radial vibration within the devices’
operating air gaps. Steady-state magnet and system offsets are
eliminated using an on-chip differential band-pass filter. This filter also
provides relative immunity to interference from RF and electromag-
netic sources. The on-chip temperature compensation and Schmitt
trigger circuitry minimizes shifts in effective working air gaps and
switch points over temperature, allowing operation to low frequencies
over a wide range of air gaps and temperatures.
Each Hall-effect digital Integrated circuit includes a voltage regu-
lator, two quadratic Hall-effect sensing elements, temperature com-
pensating circuitry, a low-level amplifier, band-pass filter, Schmitt
trigger, and an open-collector output driver. The on-board regulator
permits operation with supply voltages of 4.5 to 24 volts. The output
stage can easily switch 20 mA over the full frequency response range
of the sensor and is compatible with bipolar and MOS logic circuits.
The two devices provide a choice of operating temperature
ranges. Both devices are packaged in a 5-pin plastic SIP.
HALL-EFFECT GEAR-TOOTH SENSORS
—AC COUPLED
Always order by complete part number, e.g.,
UGS3060KA
.
D
2
ABSOLUTE MAXIMUM RATINGS
at T
A
= +25
°
C
Supply Voltage, V
CC
.............................
24 V
Reverse Battery Voltage, V
RCC
..........
-30 V
Magnetic Flux Density, B............
Unlimited
Output OFF Voltage, V
OUT
....................
24 V
Output Current, I
OUT
.........................
25 mA
Package Power Dissipation,
P
D
............................................
500 mW
Operating Temperature Range, T
A
Prefix ‘UGN’.................
-20
°
C to +85
°
C
Prefix ‘UGS’ ...............
-40
°
C to +125
°
C
Storage Temperature Range,
T
S
...............................
-65
°
C to +150
°
C
VCC
1
4
3
2
5
X
X
Dwg. PH-011
S
O
G
F
F
FEATURES
I
Senses Motion of Ferrous
Targets Such as Gears
I
Wide Operating Temperature Range
I
Operation to 30 kHz
I
Resistant to RFI, EMI
I
Large Effective Air Gap
I
4.5 V to 24 V Operation
I
Output Compatible With
All Logic Families
I
Reverse Battery Protection
I
Resistant to Physical Stress
Pinning is shown viewed from branded side.
3059
AND
3060
相關PDF資料
PDF描述
UGS3060KA HALL-EFFECT GEAR-TOOTH SENSORS -AC COUPLED
UGN3059KA AC-Coupled Hall-Effect Gear-Tooth Sensor(交流耦合霍爾效應齒輪嚙合傳感器)
UGN3060KA AC-Coupled Hall-Effect Gear-Tooth Sensor(交流耦合霍爾效應齒輪嚙合傳感器)
UGS3132 ULTRA-SENSITIVE BIPOLAR HALL-EFFECT SWITCHES
UGS3133UA ULTRA-SENSITIVE BIPOLAR HALL-EFFECT SWITCHES
相關代理商/技術參數
參數描述
UGS3059TL 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Hall-Effect Switch
UGS3060KA 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:HALL-EFFECT GEAR-TOOTH SENSORS -ACCOUPLED
UGS3060TL 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Hall-Effect Switch
UGS3113LL 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:HALL-EFFECT SWITCHES
UGS3113LT 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:HALL-EFFECT SWITCHES