- 您現在的位置：買賣IC網 > PDF目錄381166 > UDN3626M (Allegro MicroSystems, Inc.) POWERHALL SENSOR/DRIVERS FOR BRUSHLESS DC MOTORS PDF資料下載
參數資料
| 型號： | UDN3626M |
| 廠商： | Allegro MicroSystems, Inc. |
| 英文描述： | POWERHALL SENSOR/DRIVERS FOR BRUSHLESS DC MOTORS |
| 中文描述： | POWERHALL傳感器/無刷直流電機的驅動 |
| 文件頁數： | 5/8頁 |
| 文件大?。?/td> | 145K |
| 代理商： | UDN3626M |
3625
AND
3626
P
OWER
H
ALL
SENSOR/DRIVERS FOR
BRUSHLESS DC MOTORS
SENSOR LOCATION
APPLICATIONS INFORMATION
Power Dissipation.
Care should be taken in evaluating the package power
dissipation of these devices. Total power dissipated by the device will consist
of power due to the internal regulator, logic and drive circuitry (I
CC
x V
CC
),
power due to the output drivers (I
O
x V
O(SAT)
), and power due to the clamp
circuitry (I
CL
x V
CL
x duty cycle).
For example:
I
CC
x V
CC
= 38 mA (max) x 14 V = 532 mW (max)
I
O
x V
O(SAT)
= 450 mA x 0.4 V (max) = 180 mW (max)
I
CL
x V
CL
x duty cycle = 450 mA x 15 V (max) x 1% = 67.5 mW (max)
Total package power dissipation = 779.5 mW (max)
Some of the power dissipated by the device (I
CC
x V
CC
) can be reduced
by inserting a Zener diode in the supply line (Z
A
in the figure). Note that the
voltage at the V
CC
pin under worst-case conditions must be greater than the
minimum operating voltage (6.5 V).
Transient Protection.
A note of caution concerns negative (below ground)
excursions of the outputs. In application, the coupling of the two motor
windings can provide for just such a case. Reducing the coupling between
windings will help, but ground clamp diodes
or
diodes in series with the
motor windings might be required (D
C
or
D
S
in the figure). Most small
brushless motors will not require these diodes.
System requirements usually utilize a diode type of reverse-polarity
protection. If series diode protection is used with an inductive load (the usual
fan application), a Zener clamp between V
S
and ground (Z
B
in the figure) is
required. The Zener voltage must be greater than the supply voltage but less
than the rated maximum allowable supply voltage.
With diode reverse-polarity protection, a high-impedance supply, or a
switched supply line, high-voltage spikes will be generated (especially with
high-current or high-inductance loads) during normal operation, coasting, or
immediately after turn-off. In these situations, a Zener clamp (Z
B
) from V
S
to
ground will be required.
Over-Current Adjust Pin.
The over-current limit may be reduced from the
default value (I
O
MAX) by selection of an external resistor (R
ADJ
) at the
PWM/I
O
ADJ pin.
相關PDF資料 |
PDF描述 |
|---|---|
| UDN5703A | QUAD 2-INPUT PERIPHERAL/POWER DRIVERS |
| UDN-5703A | QUAD 2-INPUT PERIPHERAL/POWER DRIVERS |
| UDN5707A | QUAD 2-INPUT PERIPHERAL/POWER DRIVERS |
| UDN-5707A | QUAD 2-INPUT PERIPHERAL/POWER DRIVERS |
| UDN5733A | QUAD 2-INPUT PERIPHERAL/POWER DRIVERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UDN-5700ASERIES | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Quad Peripheral Driver |
| UDN5703 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:QUAD 2-INPUT PERIPHERAL/POWER DRIVERS-TRANSIENT-PROTECTED OUTPUTS |
| UDN5703A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:QUAD 2-INPUT PERIPHERAL/POWER DRIVERS |
| UDN-5703A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:QUAD 2-INPUT PERIPHERAL/POWER DRIVERS |
| UDN5703A/H | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SERIES 5700 LAMP, RELAY AND POWER DRIVERS |
發布緊急采購，3分鐘左右您將得到回復。