- 您現在的位置：買賣IC網 > PDF目錄381163 > UCN5804LB (Allegro MicroSystems, Inc.) BiMOS II UNIPOLAR STEPPER-MOTOR TRANSLATOR/DRIVER PDF資料下載
參數資料
| 型號： | UCN5804LB |
| 廠商： | Allegro MicroSystems, Inc. |
| 英文描述： | BiMOS II UNIPOLAR STEPPER-MOTOR TRANSLATOR/DRIVER |
| 中文描述： | BiMOS二單極性步進電機譯者/驅動器 |
| 文件頁數： | 4/8頁 |
| 文件大?。?/td> | 154K |
| 代理商： | UCN5804LB |
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
5804
BiMOS II UNIPOLAR
STEPPER-MOTOR
TRANSLATOR/DRIVER
WAVE-DRIVE SEQUENCE
Half Step = L, One Phase = H
Step
A
B
C
D
POR
1
2
3
4
ON
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
TWO-PHASE DRIVE SEQUENCE
Half Step = L, One Phase = L
Step
A
B
C
D
POR
1
2
3
4
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
ON
HALF-STEP DRIVE SEQUENCE
Half Step = H, One Phase = L
Step
A
B
C
D
POR
1
2
3
4
5
6
7
8
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
APPLICATIONS INFORMATION
Internal power-on reset (POR) circuitry resets
OUTPUT
A
(and OUTPUT
D
in the two-phase
drive format) to the on state with initial applica-
tion of the logic supply voltage. After reset, the
circuit then steps according to the tables.
The outputs will advance one sequence
position on the high-to-low transition of the STEP
INPUT pulse. Logic levels on the HALF-STEP
and ONE-PHASE inputs will determine the drive
format (one-phase, two-phase, or half-step). The
DIRECTION pin determines the rotation se-
quence of the outputs. Note that the STEP
INPUT must be in the low state when changing
the state of ONE-PHASE, HALF-STEP, or
DIRECTION to prevent erroneous stepping.
All outputs are disabled (off) when OUTPUT
ENABLE is at a logic high. If the function is not
required, OUTPUT ENABLE should be tied low.
In that condition, all outputs depend only on the
state of the step logic.
During normal commutation of a unipolar
stepper motor, mutual coupling between the
motor windings can force the outputs of the
UCN5804B below ground. This condition will
cause forward biasing of the collector-to-substrate
junction and source current from the output. For
many L/R applications, this substrate current is
high enough to adversely affect the logic circuitry
and cause misstepping. External series diodes
(Schottky are recommended for increased
efficiency at low-voltage operation) will prevent
substrate current from being sourced through the
outputs. Alternatively, external ground clamp
diodes will provide a preferred current path from
ground when the outputs are pulled below ground.
Internal thermal protection circuitry disables
all outputs when the junction temperature reaches
approximately 165
°
C. The outputs are enabled
again when the junction cools down to approxi-
mately 145
°
C.
相關PDF資料 |
PDF描述 |
|---|---|
| UCN5811 | BiMOS II 12-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS |
| UCN5811A | BiMOS II 12-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS |
| UCN5816A | 4-TO-16 LINE LATCHED DECODER/DRIVERS |
| UCN5816EP | 4-TO-16 LINE LATCHED DECODER/DRIVERS |
| UCN5818AF | BiMOS II 32-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS WITH ACTIVE-DMOS PULL-DOWNS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UCN5810A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Interface IC |
| UCN-5810A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:STEPPER-MOTOR TRANSLATORS AND DRIVERS |
| UCN5810A1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Interface IC |
| UCN-5810A-1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:STEPPER-MOTOR TRANSLATORS AND DRIVERS |
| UCN5810A-1 | 制造商:Allegro MicroSystems LLC 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。